Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Verify Diagnostic Display Output Functions
B.  If the output LED’s are on  as specified, but the
machine does  not function properly,  consider that
the controller is  operating correctly and a  problem
exists with some other component. Inspect electrical
components  and circuit  for  the affected  function.
Also, suspect a non-electrical problem (e.g. hydrau-
lic component problem). Repair as necessary.
The Diagnostic  Display also  has the  ability to detect
which output solenoids or  relays are turned on by the
TEC controller. This is a quick way to determine if a ma-
chine malfunction is electrical or hydraulic.
NOTE:  Anopenoutput(e.g.anunpluggedconnectoror
a broken wire) cannot be detected with the Diagnostic
Display.
C. If each input switch is in the correct position and
functioning correctly,  but the output LED’s  are not
correctly illuminated, this indicates a controller prob-
lem. If this occurs, contact your Toro Distributor for
assistance.
1.
decks, stop the engine and engage the parking brake.
Park machine on a level  surface, lower the cutting
2.
connectors near TEC controller. Carefully unplug loop-
back connector from harness connector (Fig. 12).
Open control panel cover. Locate wire harness and
7.
After output  function testing is  completed, discon-
nect the  Diagnostic Display  from wire  harness. Plug
loopback connector into harness connector. Install con-
trol panel cover.
3.
ConnecttheDiagnosticDisplayconnectortothehar-
nessconnector.Makesurecorrectoverlaydecalisposi-
tioned on the Diagnostic Display (Fig. 13).
4.
Turn the ignition switch to the RUN position.
NOTE:  The red text on the overlay decal refers to con-
troller inputs and the green text refers to controller out-
puts.
3
5.
The green “OUTPUTS DISPLAYED” LED, on lower
2
1
right column of the Diagnostic Display, should be illumi-
nated.  If “INPUTS  DISPLAYED”  LED  is illuminated,
press the  toggle button  on the Diagnostic  Display to
change the LED to “OUTPUTS DISPLAYED”.
Figure 12
NOTE:  It may  be necessary  to  toggle between  “IN-
PUTS DISPLAYED” and “OUTPUTS DISPLAYED” sev-
eral times to perform the following step. To change from
inputs to outputs, press toggle button once. This may be
done as  often  as required.  Do not  press and  hold
toggle button.
1.
2.
TEC controller location
Loopback connector
3.   Harness connector
DIAGNOSTIC
DISPLAY
OVERLAY
117--0171
6.
Sit on seat, start engine and attempt to operate the
desired function of the machine. The appropriate output
LED’s should illuminate on the Diagnostic Display to in-
dicate that the TEC controller is turning on that function.
NOTE:  If the “DIAG. LAMP” output LED is blinking, this
indicates that the  TEC controller has  detected a fault
during machine operation. Refer to Diagnostic Light in
this section for information on retrieval and clearing of
controller faults.
A.  IfthecorrectoutputLED’sdonotilluminate,verify
that the required input switches are in the necessary
positions to  allow that function  to occur (see TEC
Controller Logic Chart in this section). Verify correct
switch function.
Figure 13
Electrical System
Page 5 -- 10
Groundsmaster 4300--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website