Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Blade Spindle Service
Disassembly (Fig. 5)
2
6
1.
Remove blade spindle from cutting deck (see Blade
Spindle Removal in this section).
4
2.
shaft.
Loosen and remove spindle nut from top of spindle
130 to 160 ft--lb
11
(177
to 216 N--m)
10
3.
Remove the spindle shaft from the spindle housing
whichmayrequiretheuseofanarborpress.Thespindle
shaft spacer should remain on the spindle shaft as the
shaft is being removed.
9
8
12
7
1
4.
Carefully remove oil seals from spindle housing not-
ing direction of seal lips.
4
5
5.
spacer ring to drop out of the spindle housing.
Allow the bearing cones, inner bearing  spacer and
6.
cups and the outer bearing spacer from the housing.
Using an arbor  press, remove both  of the bearing
3
7.
housing. Removal of this snap ring is very difficult.
The large snap  ring can remain inside  the spindle
Assembly (Fig. 5)
Figure 5
1.
2.
3.
4.
5.
6.
Spindle housing
Spindle plug
Spindle shaft
Oil seal
Shaft spacer
Spindle nut
7.
8.
9.
10. Spacer set (2 piece)
11. Bearing
12. Large snap ring
Grease fitting (2 used)
Bearing
NOTE:  Areplacement spindle bearing set contains two
(2)
bearings, a spacer ring and a large snap ring (items
Spacer ring
1,
2 and 3 in Fig. 6). These parts cannot be purchased
separately. Do  not mix bearing  set components  from
one deck spindle to another.
NOTE:  A replacement bearing spacer set includes the
inner spacer and outer spacer (items 4 and 5 in Fig. 6).
Do not mix bearing  spacers from one deck spindle  to
another.
1
4
IMPORTANT: If  new bearings  are  installed into  a
usedspindlehousing,itmaynotbenecessarytore-
place the  original  large snap  ring. If  the  original
large snap  ring is  in good  condition with no  evi-
denceofdamage  (e.g.spunbearing), leavethesnap
ring in the housing and discard the large snap ring
that comes with the new bearings. If the large snap
ring is found to be damaged, replace the snap ring.
2
5
3
1
Figure 6
1.
Iflargesnapringwasremovedfromspindlehousing,
install snap ring into housing groove.  Make sure snap
ring is fully seated in groove.
1.
2.
3.
Bearing
Spacer ring
Large snap ring
4.   Inner bearing spacer
5.   Outer bearing spacer
2.
ing. The spacer should fit against the large snap ring.
Install outer bearing spacer into top of spindle hous-
Cutting Decks
Page 7 -- 10
Groundsmaster 4300--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website