Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Removal (Fig. 8)
Park  machine  on  a  level  surface,  lower  cutting
decks, stop  engine, apply  parking brake and remove
key from the ignition switch.
10.Carefully pull radiator assembly  from the machine.
Plug radiator and hose openings to prevent contamina-
tion.
1.
11.Inspect all foam seals placed between radiator, fan
shroud  and radiator  frame.  Replace damaged  foam
seals.
2.
Raise and support the hood.
Installation (Fig. 8)
CAUTION
1.
Remove plugs placed in radiator and hose openings
during the removal procedure.
Do not open radiator cap or drain coolant if the
radiator or engine is hot. Pressurized, hot cool-
ant can escape and cause burns.
2.  Carefully position radiator assembly to  the radiator
support. Position fan shroud to the radiator.
Ethylene--glycol  antifreeze  is poisonous.  Dis-
pose of coolant properly, or store it in a properly
labeled container away from children and pets.
3.
Securefanshroudandradiatortoradiatorframe    with
removed flange  head screws  and flange  nuts. Make
sure that at least 0.250” (6.4 mm) clearance exists at all
points between shroud opening and fan.
3.
Drain coolant from radiator.
4.
Position coolant  reservoir and brackets  to the  fan
A.  Slowly remove radiator cap from the radiator.
shroud.  Secure reservoir  to fan  shroud  and radiator
frame with two (2) flange head screws and flange nuts.
B.  Place drain pan below the radiator draincock lo-
cated on the bottom of the radiator. Make sure that
drainpanislargeenoughto   holdcoolingsystemcon-
tents (10 U.S. quarts (9.5 liters)).
5.  Place spacers (item 43) into holes in foam seal (item
42). Position foam seal and air intake screen (item 37)
to radiator frame. Secure intake screen to machine with
five (5) flange head screws and flange nuts.
C. Loosen  radiator draincock (threaded in) and al-
low coolant to drain from radiator.
6.  Connect upper and lower radiator hoses to radiator
and secure with clamps.
4.
5.
Remove screen from machine.
7.
Connect overflow  hose to radiator fill  opening and
Disconnect radiator  hoses (upper and lower)  from
secure with hose clamp.
the radiator.
8.  Makesure radiatordraincock isclosed  (threadedout
fully).
6.
Loosen hose clamp and remove overflow hose from
radiator fill opening.
9.
To allow air to escape during radiator filling, remove
7.
Remove two (2) flange head screws and flange nuts
pipe plug (item 8) from top of radiator. Fill radiator with
coolant. Make sureto installplug onceall airis bledfrom
radiator.
that  secure  coolant   reservoir  and  brackets  to  fan
shroud. Carefully position reservoir and brackets away
from the fan shroud.
10.After
radiator has been properly filled with  coolant,
8.
Remove five (5) flange head screws and flange nuts
install radiator cap.
that secure air intake screen (item 37) to machine. Re-
move screen and foam seal  (item 42). Locate and re-
trieve five (5) spacers (item 43).
11.Lower and secure hood.
9.
cure fan shroud and radiator to radiator frame. Position
Remove flange head screwsand flangenuts that se-
fan shroud away from the radiator.
Groundsmaster 4300--D
Page 3 -- 11
Kubota Diesel Engine
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website