Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Parking Brake Switch
The parking brake switch is a normally open proximity
switch. The parking brake switch is attached to the bot-
tom of  the brake  pedal (Fig.  32). The  parking brake
switch is used as an input for the TEC controller.
D. Turn  ignition switch to  the ON position  (do not
start engine) and  verify with a multimeter that  ma-
chine wire harness connector terminal for pink wire
has system voltage (12 VDC) present.
Whentheparkingbrakeisnotapplied,theparkingbrake
detent is positioned near the target end of the parking
brake switch so the switch is closed. The parking brake
detent is moved away from the switch when the parking
brake is applied causing the switch to open.
E.  If black wire is  closed to ground, pink  wire has
system voltage present and switch LED did not func-
tion, replace parking brake switch. Adjust switch af-
ter  installation (see  Parking  Brake  Switch in  the
Adjustments section of this chapter).
Testing
5.  If the parking brake switch tests correctly and a cir-
cuit problem still exists, check wire harness (see Electri-
cal  Schematic and  Circuit  Drawings in  Chapter  8 --
Foldout Drawings).
1.
Before disconnecting  the parking brake  switch for
testing, the switch and its circuit wiring should be tested
as a TEC  controller input with the  Diagnostic Display
(see Diagnostic Display in the Troubleshooting section
ofthischapter).IftheDiagnostic   Displayverifies  thatthe
parking brake switch and circuit wiring are functioning
correctly, no further switch testing is necessary. If, how-
ever,theDiagnostic  Displaydetermines thattheparking
brake switch and circuit wiring are not functioning cor-
rectly, proceed with testing procedure.
6.  Make sure that parking brake switch is connected to
wire harness when testing is complete.
2.
Turn ignition switch to the ON position (do not start
engine) and check LED  on cable end of brake  switch
(Fig. 32). LED should be illuminated when the parking
brake is not applied.
5
3.
With the ignition switch still in the ON position (do not
start engine), apply  parking brake and check  LED on
cable end of parking brake switch. LED should not be
illuminated when the parking brake is applied.
3
4.
If the brake switch LED did not function correctly:
2
4
A.  Make sure that brake switch is properly adjusted
(see Parking Brake Switch in the Adjustments sec-
tion of this chapter). If necessary, adjust switch and
return to step 2 above.
3
1
B.  Make sure ignition switch is OFF and disconnect
the parking  brake switch  connector  from the ma-
chine wire harness.
6
Figure 32
C. Verify  that the machine wire harness connector
terminal  for  black  wire  is  closed   (continuity)  to
ground.
1.
2.
3.
Parking brake switch
Lock washer (2 used)
Jam nut (2 used)
4.
5.
6.
Parking brake detent
Brake pedal
Switch LED location
Electrical System
Page 5 -- 30
Groundsmaster 4300--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website