Maintenance and Service
1.
ting decks, stop engine, apply parking brake and re-
move key from the ignition switch.
Before servicing or making adjustments, lower cut-
12.Disconnect battery before servicing the machine.
Disconnect negative battery cable first and positive
cable last. If battery voltage is required for troubleshoot-
ing or test procedures, temporarily connect the battery.
Reconnect positive battery cable first and negative
cable last.
2.
keeping all nuts, bolts and screws tight.
Make sure machine is in safe operating condition by
3.
wherethereisanopenflame, suchasnearawaterheat-
er or furnace.
Never store the machine or fuel container inside
13.Battery
Avoid contact with skin, eyes and clothing. Protect your
face, eyes and clothing when working with a battery.
acid is poisonous and can cause burns.
4.
all hydraulic hoses and lines are in good condition be-
fore applying pressure to the hydraulic system.
Make sure all hydraulic line connectorsare tight, and
14.Battery
and flames away from the battery.
gases can explode. Keep cigarettes, sparks
15.When
changing attachments, tires or performing
5.
Keepbodyandhandsawayfrom pinholeleaksinhy-
other service, use correct supports, hoists and jacks.
Make sure machine is parked on a solid level floor such
as a concrete floor. Prior to raising the machine,remove
any attachments that may interfere with the safe and
proper raising of the machine. Always chock or block
wheels. Use jack stands or appropriate load holding de-
vices to support the raised machine. If the machine is
not properly supported, the machine may move or fall,
which may result inpersonal injury(see JackingInstruc-
tions in this section).
draulic lines that eject high pressure hydraulic fluid. Use
cardboard or paper to find hydraulic leaks. Hydraulic
fluid escaping under pressure can penetrate skin and
cause injury. Fluid accidentally injected into the skin
must be surgically removed within a few hours by a doc-
tor familiar with this form of injury or gangrene may re-
sult.
6.
Before disconnecting or performing any work on the
hydraulic system, all pressure in the system must be re-
lieved by using all of the hydraulic controls (see Reliev-
ing Hydraulic Pressure in the General Information
section of Chapter 4 -- Hydraulic System).
16.If
major repairs are ever needed or assistance is de-
sired, contact an Authorized Toro Distributor.
17.When
welding on machine, disconnect all battery
7.
decks. Wear gloves and use caution when servicing
them.
Use care when checking or servicing the cutting
cables to prevent damage to machine electronic equip-
ment. Disconnect negative battery cable first and posi-
tive cable last. Also, disconnect the wire harness
connector from the machine controller and disconnect
the terminal connector from the alternator. Attach weld-
er ground cable no more than two (2) feet (0.61 meters)
from the welding location.
8.
free of excessive grease, grass, leaves and dirt. Clean
protective screen on machine frequently.
To reduce potential fire hazard, keep engine area
9.
If engine must be running to perform maintenanceor
18.At
the time of manufacture, your Groundsmaster
to make an adjustment, keep hands, feet, clothing and
other parts of the body away from the cutting decks and
other moving parts. Keep bystanders away.
conformed to the safety standards for riding mowers. To
assure optimum performance and continued safety cer-
tification of the machine, use genuine Toro replacement
parts and accessories. Replacement parts and acces-
sories made by other manufacturers may result in non-
conformance with the safety standards, and the
warranty may be voided.
10.Do
setting. Toassuresafety andaccuracy,checkmaximum
engine speed with a tachometer.
not overspeed the engine by changing governor
11.
Shut engine off before checking or adding oil to the
crankcase.
Safety
Page 1 -- 4
Groundsmaster 4300--D
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Groundsmaster 4300 D |
Download File |
|
Document Type | Catalog |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)