Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Removal (Fig. 65)
Park themachine onalevelsurface,  engage parking
Installation (Fig. 65)
1.
1.  Applyantiseizelubricanttotractionpumpinputshaft.
brake, lower  cutting decks and  stop engine. Remove
key from the ignition switch.
2.
put shaft.
Positiondriveshaftassemblytoengineandpumpin-
2.
that secure drive shaft guard hoop (item 4) to machine
frame. Remove guard.
Remove two (2) flange head screws and flange nuts
3.
Apply Permatex Blue Gel Threadlocker (or equiva-
lent) to threads of cap screws (item 7) that secure drive
shaft  flange  to  engine flywheel.  Secure  drive  shaft
flange  to flywheel  with  six (6)  cap  screws  (item 7).
Torque cap screws from 34 to 42 ft--lb (46 to 56 N--m).
3.
(item9)thatsecuredriveshaftyoketopistonpumpinput
shaft.
Remove two (2) cap screws (item 5) and flange nuts
4.
Slide drive shaft yoke on pump input shaft so yoke is
4.
shaft flange to engine flywheel.
Remove six (6) cap screws (item 7) that secure drive
flush with end of input shaft. Secure drive shaft yoke to
pump input shaft with two (2) cap screws (item 5) and
flange nuts (item 9).
5.
Remove drive shaft assembly from machine.
Drive Shaft Cross and Bearing Service (Fig. 66)
Remove snap rings that secure bearings in yokes.
5.
Position drive  shaft guard hoop to  machine frame
and secure with two (2) flange head screws and flange
nuts.
1.
6.
Lubricate grease fittings on drive shaft.
IMPORTANT: Yokes  must be  supported  when re-
moving and installing bearings to prevent damage.
4
2.
yokes. Thoroughly clean drive shaft yokes.
Use a  press  to remove  cross and  bearings  from
3
2
3.
To install new cross and bearings:
1
A.  Apply a coating of grease to bearing bores in end
yoke and shaft yoke.
B.  Press one bearing partially into yoke.
C. Insert cross into yoke and bearing.
D. Hold cross in alignment and press bearing inuntil
it hits the yoke.
3
E.  Install  snap  ring  into yoke  groove  to  secure
installed bearing.
Figure 66
F.  Place second  bearing into yoke  bore and onto
cross shaft. Press bearing into yoke and secure with
snap ring.
1.
2.
End yoke
Cross and bearing kit
3.
4.
Snap ring (4 used)
Shaft yoke
G. Repeat procedure for other yoke.
H. Greasecrossuntilgreasecomesoutofallfour(4)
cups.
4.
Make sure that assembled joint moves without bind-
ing. Slight binding can usually  be eliminated by lightly
rapping the yoke lugs with a soft faced hammer. If bind-
ing continues,  disassemble joint  to identify source  of
binding.
Groundsmaster 4300--D
Page 4 -- 67
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website