Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Removal (Fig. 75)
10.Label  all hydraulic  hoses for  assembly purposes.
Remove hydraulic hoses from fittings on wheel motor.
Allow hoses to drain into a suitable container.
CAUTION
11.
Putclean plugs in disconnected hydraulic hoses and
fittings to prevent system contamination.
Before opening hydraulic system, operate all hy-
draulic controls to relieve system pressure and
avoid injury from pressurized hydraulic oil. See
Relieving Hydraulic System Pressure in the Gen-
eral Information section of this chapter.
12.Support
ing removal.
thewheelmotortopreventitfromfallingdur-
13.Remove four (4) cap screws and lock washers that
secure wheel motor to the steering spindle.
1.
Park themachine onalevelsurface,  engage parking
brake, lower  cutting decks and  stop engine. Remove
key from the ignition switch.
14.Remove
wheel motor from frame.
15.If
necessary, remove  hydraulic fittings from  wheel
motor. Remove and discard O--rings from fittings.
2.
Read the  General Precautions  for Removing  and
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
Installation (Fig. 75)
IMPORTANT: Because  of   internal  differences  in
rear wheel motors, DO NOT interchange rear wheel
motors on machine (i.e. do not put right side motor
on left side of machine). The left side wheel motor
has a yellow identification mark on the motor hous-
ing. If necessary, use parts catalog and part number
on wheel motor to identify RH and LH motors.
3.
Chock frontwheelstopreventmachine  fromshifting.
4.
and lock nut (item 14) that secures wheel hub to wheel
motor.
Loosen, but do not remove, five (5)  wheel lug nuts
WARNING
1.
If fittings were removed from wheel motor, lubricate
and install new O--rings to  hydraulic fittings. Install fit-
tingsintowheelmotorports(seeHydraulicFittingInstal-
lationintheGeneralInformation   sectionofthischapter).
Beforejackingupthemachine,reviewandfollow
Jacking Instructions in Chapter 1 -- Safety.
2.
sure that ports in wheel motor are facing toward the rear
of the machine.
Position rear wheel motor to steering spindle. Make
5.
rear wheel. Support machine with jack stands.
Jack up machine enough to allow the removal of the
6.
RearWheelRemovalintheServiceandRepairssection
of Chapter 6 -- Chassis).
Removerearwheelassemblyfromthemachine(see
3.
screws and lock washers.
Secure  wheel motor  to  spindle with  four (4)  cap
4.
hoses and wheel motor fittings that were placed during
wheel motor removal to prevent contamination.
Remove caps or plugs from disconnected hydraulic
IMPORTANT: DO  NOT  hit  wheel hub,  wheel  hub
puller or wheel motor with a hammer during wheel
motor  removal  or   installation.  Hammering  may
cause damage to the wheel motor.
5.
Using  labels placed  during  the removal  process,
properly connect hydraulic hoses to wheel motor fittings
(see Hydraulic Hose and Tube Installation in the Gener-
al Information section of this chapter).
7.
Make sure that lock nut (item 14) that secures wheel
hub to wheel motor is  loosened at least two (2) turns.
Usehubpuller(seeSpecialToolsinthischapter)toloos-
en wheel hub from wheel motor.
6.
Make  sure that  tapers  of wheel  motor  shaft and
wheel hub are thoroughly clean.
8.
Remove loosened lock nut and wheel hub from mo-
tor shaft. Discard lock nut. Locate and retrieve woodruff
key from wheel motor shaft.
7.
Positionwoodruffkeytokeyslotinwheelmotorshaft.
IMPORTANT: Do  not reuse  lock  nut that  secures
wheelhubtowheelmotorafterithasbeenremoved.
9.
rear wheel motor to prevent hydraulic system contami-
nation.
Thoroughlycleanhydraulichoseendsandfittingson
Groundsmaster 4300--D
Page 4 -- 81
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website