Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Component Testing
For accurate resistance and/or continuity checks, elec-
trically disconnect the component being tested from the
circuit (e.g. unplug the ignition switch connector before
doing a continuity check of the switch).
NOTE:  For engine component testing information, see
the Kubota Workshop Manual, Diesel Engine, 05--E3B
Series at the end of Chapter 3 -- Kubota Diesel Engine.
NOTE:  Electrical troubleshooting of any 12 volt power
connectioncanbeperformedthroughvoltagedroptests
without disconnecting the component.
CAUTION
When testing electrical components for continu-
ity with a multimeter (ohms setting), make sure
that power to the circuit has been disconnected.
NOTE:  Use the Diagnostic Display (see Special Tools
in this chapter) to test TEC controller inputs and outputs
before further troubleshooting of an electrical problem
on your Groundsmaster.
Ignition Switch
The ignition (key) switch has three positions (OFF, RUN
and START). The switch is mounted on the control con-
sole.
5.  If switch tests correctly and  circuit problem still ex-
ists, check wire harness (see Electrical Schematic and
Circuit Drawings in Chapter 8 -- Foldout Drawings).
Testing
6.  Connect  wire harness  electrical  connector to  the
ignition switch.
1.
Before disconnecting the ignition switch for testing,
the switch and  its circuit wiring should be  tested as a
TEC controller  input with the Diagnostic  Display (see
DiagnosticDisplayintheTroubleshootingsectionofthis
chapter). If the Diagnostic Display verifies that ignition
switch andcircuit wiring arefunctioning correctly,nofur-
ther switch testing is necessary. If, however, the Diag-
nostic Display determines thatignition switch andcircuit
wiring are not  functioning correctly, proceed with test
procedure.
7.  Install control  arm cover  to machine  (see Control
Arm Assembly  in the Service  and Repairs section  of
Chapter 6 -- Chassis).
RUN
45o
45o
OFF
START
2.
Remove outside control arm cover to gain access to
A
F
ignitionswitch(seeControlArmDisassembly   intheSer-
vice and Repairs section of Chapter 6 -- Chassis). Dis-
connect  wire  harness  electrical  connector  from the
switch.
E
B
C
D
FRONT VIEW
REAR VIEW
Figure 18
3.
With  the use  of a  multimeter  (ohms setting),  the
switch functions  may be tested to  determine whether
continuity exists between the various terminals for each
switch  position.   The  ignition   switch  terminals   are
marked as  shown  in Figure  18. The  circuitry  of this
switch is shown in the chart below. Verify continuity be-
tween switch terminals.
POSITION
OFF
CIRCUIT
NONE
RUN
B + C + F,  D + E
A + B + C
START
4.
Replace ignition switch if necessary.
Electrical System
Page 5 -- 22
Groundsmaster 4300--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website