Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

PTO Switch
The PTO switch is mounted on the control panel and al-
lows the cutting decks to operate when the front of the
switch is  depressed. An  indicator light  on the  switch
identifies when the PTO switch is engaged.
7.  Connect  wire harness  electrical  connector to  the
PTO switch.
8.
Install control  arm cover  to machine  (see Control
Arm Assembly  in the Service  and Repairs section  of
Chapter 6 -- Chassis).
The TEC  controller monitors the  position of  the PTO
switch (up or down). Using inputs from the PTO switch
andotherswitches  intheinterlock system, thecontroller
controls the energizing of the hydraulic solenoid valves
used to drive the cutting deck motors.
NOTE:  To engage the PTO, the seat has  to be occu-
pied, the mow speed limiter has to be in the mow posi-
tion and the cutting decks have to be fully lowered.
Testing
1.
Before disconnecting the PTO switch for testing, the
1
switch and its circuit wiring should be tested as a TEC
controller input with the Diagnostic Display  (see Diag-
nostic Display  in  the Troubleshooting  section of  this
chapter). If the Diagnostic Display verifies that the PTO
switch andcircuit wiring arefunctioning correctly,nofur-
ther switch testing is necessary. If, however, the Diag-
nostic  Display determines  that  the  PTO  switch and
circuit wiring are not functioning correctly, proceed with
test procedure.
2.
switch(seeControlArmDisassembly   intheServiceand
Repairs section of Chapter 6 -- Chassis).
Remove control arm covers to gain access to PTO
Figure 23
3.
connect wire harness electrical connector from the PTO
switch.
Make sure ignition switch is in the OFF position. Dis-
1.
PTO switch
4.
With  the use  of a  multimeter  (ohms setting),  the
switch functions  may be tested to  determine whether
continuity exists between the various terminals for each
switch position. The PTO switch terminals are marked
as shown  in Figure 24.  The circuitry of  this switch  is
shown  in the  chart below.  Verify  continuity between
switch terminals.
BACK OF SWITCH
SWITCH
POSITION
NORMAL
CIRCUITS
OTHER
CIRCUITS
Figure 24
ON
2 + 3
2 + 1
5 + 6
5 + 4
NOTE:  PTO switch terminals 7 and 8 are for the switch
indicator light.  Switch terminals 1, 4,  5 and 6  are not
used on Groundsmaster 4300--D machines.
OFF
5.
6.
exists, check  wire harness  (see Electrical Schematic
and Circuit Drawings in Chapter 8 -- Foldout Drawings).
Replace PTO switch if necessary.
If PTO switch tests correctly and circuit problem still
Groundsmaster 4300--D
Page 5 -- 25
Electrical System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website