Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Removal (Fig. 64)
Park themachine onalevelsurface,  engage parking
brake, lower  cutting decks and  stop engine. Remove
key from the ignition switch.
Installation (Fig. 64)
1.
1.  If fittings were removed from reservoir, lubricate and
place new O--rings onto fittings. Installfittings intoreser-
voir openings  using marks  made during  the removal
process  to properly  orientate fittings.  Tighten fittings
(see Hydraulic Fitting Installation in  the General Infor-
mation section of this chapter).
2.
hydraulic reservoir to prevent hydraulic  system conta-
mination. Label hydraulic hoses to assist in installation.
Thoroughlycleanhydraulichoseendsandfittingson
2.
Lubricate  new suction  strainer O--ring  and  install
3.
ting on bottom of reservoir to allow draining of reservoir.
Drain reservoir into a suitable container.
Disconnect hydraulic hose (item 7) from adapter fit-
onto strainer. Thread suction strainer into hydraulic res-
ervoir and torque strainer 105 to 115 ft--lb (143 to 155
N--m).
4.
Disconnect remaining  hydraulic hoses from reser-
3.
servoir to frame with two (2) clamps (item 13), washer
head screws (item 12) and flange nuts (item 14).
Position hydraulic reservoir to machine. Secure re-
voir.Allowhydrauliclinestodrainintoasuitablecontain-
er.Plugorcapopenings   ofreservoir andlines toprevent
contamination.
4.
tings during the removal process.
Remove all plugs and caps placed in hoses and fit-
5.
guide.
Remove hydraulic  reservoir using  Figure 64  as a
5.
Install hydraulic hoses to fittings on hydraulic reser-
6.
ring.
Remove suction strainer from reservoir. Discard O--
voir in  positions noted during removal  (see Hydraulic
Hose and Tube Installation in the General Information
section of this chapter).
7.
If hydraulic fittings are to be removed from reservoir,
mark fitting orientation  to allow correct assembly. Re-
move fittings from reservoir and discard O--rings.
6.
7.
forleaks.Tightenanylooseconnections.Checkhydrau-
lic oil level and adjust if necessary.
Fill hydraulic reservoir with new hydraulic fluid.
Operate machine. Check hydraulic lines and fittings
Inspection (Fig. 64)
1.
Clean hydraulic reservoir and  suction strainer with
clean solvent.
2.
Inspect hydraulic reservoir for leaks, cracks or other
damage.
Groundsmaster 4300--D
Page 4 -- 65
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website