Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

14.To
test individual front wheel motors:
CAUTION
A.  Remove front wheel from wheel motor that is not
being tested. Remove wheel shield to allow access
to hydraulic tubes and fittings on  wheel motor. Re-
move fasteners that  secure front hydraulic tube r--
clamps to frame.
Before opening hydraulic system, operate all hy-
draulic controls to relieve system pressure and
avoid injury from pressurized hydraulic oil. See
Relieving Hydraulic System Pressure in the Gen-
eral Information section of this chapter.
B.  On the front wheel motor that is not being tested,
thoroughlycleanjunctionofbothhydraulictubesand
wheel motor fittings. Disconnect both hydraulic lines
from wheel motor that is not being tested. Cap dis-
connected hydraulic lines and wheel motor fittings.
5.
Attachaheavychaintotherearofthemachineframe
and an immovable object to prevent the machine from
moving during testing.
C. Use  the procedure  described in  steps 8  to 11
above to identify individual front  wheel motor leak-
age. Individual motor internal leakage will be shown
on flow meter in GPM (LPM).  Flow should be less
than 1.5 GPM (5.7 LPM) for the tested wheel motor.
6.
sure parking brake is applied.
Chock front wheels to prevent wheel rotation. Make
7.
to allow flow through the rear wheel motors.
Jack up and support the rear wheels off the ground
D. If other front wheel motor requires testing, com-
plete steps A, B and C for remaining wheel motor.
8.
Thoroughly  clean junction  of  hydraulic  hose and
right side elbow fitting on bottom of traction pump (Fig.
Disconnect hose from right side pump fitting.
42).
15.After
testing is completed, stop engine and then re-
lieve hydraulic system pressure (see Relieving Hydrau-
lic System Pressure in the General Information section
of this chapter). Disconnect tester from hydraulic fitting
and hose. Connect hose to pump elbow fitting. Remove
caps from hydraulic tubes and reconnect tubes to wheel
motor.Securehydraulictubestomachinewithr--clamps
and  removed   fasteners.   Install  wheel   shield  and
wheel(s) (see Wheels in the Service and Repairs sec-
tion of Chapter 6 -- Chassis).
IMPORTANT: Make sure  that the oil flow  indicator
arrow on the flow meter is showing that the oil will
flow from the pump, through the tester and into the
disconnected hydraulic hose.
9.
Install tester with pressure gauges and flow meter in
series  with the  traction  pump and  the  disconnected
hose. Make sure the tester flow control valve is fully
open.
10.Start
engine and move  throttle to full speed   (3200
RPM).
1
CAUTION
Use extreme caution when performing test. The
front tires on the ground will  be trying to move
the machine forward.
4
2
11.
1000
Slowly push traction pedal in forward direction until
PSI (70 bar) is displayed  on the tester pressure
5
gauge. Make sure that front wheels are not rotating.
RIGHT
3
12.Total
front  wheel  motor  internal  leakage  will  be
FRONT
shown on flow  meter in GPM (LPM). Leakage  for the
front wheel motors should be less than 1.5 GPM  (5.7
LPM).
Figure 42
13.Release
traction pedal, shut engine off, rotate both
1.
2.
3.
Traction pump
RH elbow fitting
Hyd hose (forward)
4.
5.
LH elbow fitting
Hyd hose (reverse)
front wheels one--third turn and retest. Testing of wheel
motor leakage in three (3) different wheel positions will
providethemostaccuratetestresults.Ifleakagespecifi-
cations are not met, individual front wheel motors need
to be tested.
Groundsmaster 4300--D
Page 4 -- 41
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website