Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Removal (Fig. 3)
Park  machine  on  a  level  surface,  lower  cutting
decks, stop engine, engage parking brake and remove
key from the ignition switch.
5.  Remove cover from top of spindle that was placed to
prevent debris from entering spindle.
1.
6.  Make sure that O--ring is positioned to top of spindle
housing. Secure hydraulic motor tothecutting deck with
two (2) socket head screws and flat washers.
2.
Remove two (2) socket head screws and flat wash-
ers that secure hydraulic motor to the cutting deck (Fig.
IMPORTANT: Pneumatic grease guns can produce
high pressure inside spindle housing that can dam-
age spindle seals.  Pneumatic grease guns,  there-
fore, are not recommended to be used for greasing
of spindle housings.
4).
3.
Remove hydraulic motor and O--ring from deck.
Cover top of spindle to prevent debris from entering
spindle. A spindle plug (see Special Tools in this chap-
ter) can be used to cover spindle.
7.
fittingsonhousingandfillhousing   cavitywithgreaseun-
til grease starts to come out of lower seal.
Attach a hand pump grease gun to one of the grease
4.
Start the engine and raise the cutting deck. Stop en-
gine and remove key from the ignition switch. Support
the cutting deck so it cannot fall accidentally. If required
for easier service, remove cutting deck from machine.
8.  After assembly, raise and lower the cutting deck to
verify that hydraulic  hoses and fittings  do not contact
anything.
5.
blade.
Remove  blade  bolt,  anti--scalp  cup   and  cutting
6.
Remove six (6) flange nuts that secure  spindle as-
sembly to cutting deck. Slide spindle assembly out the
bottom of the deck.  Remove spindle plate from top of
deck.
7.
If necessary, press studs from spindle housing.
Installation (Fig. 3)
If studs were removed from spindle housing, press
1
1
2
1.
studs fully into housing holes. Make sure that stud head
is seated squarely against housing.
2.
ting deck. Align grease fittings on spindle with notches
on cutting deck and spindle plate toward front of deck.
Position spindle assembly and spindle plate to cut-
Figure 4
1.
Socket head screw
2.   Hydraulic motor
3.
Secure spindle  to cutting  deck with  six (6) flange
nuts. Tighten flange nuts in a star pattern.
4.
Tighten blade  bolt from  85 to  110 ft--lb  (115 to 149
N--m).
Install cutting blade, anti--scalp cup and blade bolt.
Groundsmaster 4300--D
Page 7 -- 9
Cutting Decks
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website