Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Traction Neutral Switch
The traction neutral switch is a normally open proximity
switch that closes when the traction pedal is in the neu-
tral position. The switch mounts to a bracket on the trac-
tion pump (Fig. 31). The  sensing plate for the traction
neutralswitchisthetractionleverbracketthatissecured
to the pump control arm. The neutral switch is used as
an input for the TEC controller.
D. Turn  ignition switch to  the ON position  (do not
start engine) and  verify with a multimeter that  ma-
chine wire harness connector terminal for pink wire
has system voltage (12 VDC) present.
E.  If black wire is  closed to ground, pink  wire has
system voltage present and switch LED did not func-
tion, replace traction neutral switch. Adjust switch af-
ter installation  (see Traction Neutral  Switch in the
Adjustments section of this chapter).
Testing
1.
Before disconnecting the traction neutral switch for
testing, the switch and its circuit wiring should be tested
as a TEC  controller input with the  Diagnostic Display
(see Diagnostic Display in the Troubleshooting section
ofthischapter).IftheDiagnostic   Displayverifies  thatthe
traction neutral switch and circuit wiring are functioning
correctly, no further switch testing is necessary. If, how-
ever,theDiagnostic  Display determines thatthetraction
neutral switch and circuit wiring are not functioning cor-
rectly, proceed with testing procedure.
5.  If the neutral switch tests correctly and a circuit prob-
lem still exists, check wire harness (see Electrical Sche-
matic  and Circuit  Drawings  in  Chapter  8 --  Foldout
Drawings).
6.
to wire harness when testing is complete.
Make sure that traction neutral switch is connected
FRONT
3
5
2.
Turn ignition switch to the ON position (do not start
6
engine) and check LED on cable end of neutral switch
(Fig. 31). LED should be illuminated when the traction
pedal is in the neutral position.
4
3.
With the ignition switch still in the ON position (do not
startengine),presstractionpedaloutoftheneutralposi-
tion and check LED on cable end of neutral switch. LED
should not be  illuminated when the traction  pedal is
not in the neutral position.
2
6
1
4.
If the neutral switch LED did not function correctly:
5
A.  Makesurethatneutralswitchisproperlyadjusted
(see Traction Neutral Switch inthe Adjustments sec-
tion of this chapter). If necessary, adjust switch and
return to step 2 above.
7
Figure 31
1.
2.
3.
4.
Traction pump
5.
Jam nut (2 used)
Lock washer (2 used)
Switch LED location
Traction neutral switch
Traction lever bracket
Pump control arm
6.
7.
B.  Make sure ignition switch is OFF and disconnect
the traction neutral  switch connector from the  ma-
chine wire harness.
C. Verify  that the machine wire harness connector
terminal  for  black  wire  is  closed   (continuity)  to
ground.
Groundsmaster 4300--D
Page 5 -- 29
Electrical System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website