Battery Service
The battery is the heart of the electrical system. With
regular andproper service, battery lifecan beextended.
Additionally, battery and electrical component failure
can be prevented.
7
6
8
FRONT
1
4
CAUTION
3
When working with batteries, use extreme cau-
tion to avoid splashing or spilling electrolyte.
Electrolyte can destroy clothing and burn skin or
eyes. Always wear safety goggles and a face
shield when working with batteries.
2
Electrolyte Specific Gravity
Fully charged: 1.265 corrected to 80oF (27oC)
5
Discharged: less than 1.240
Figure 57
Battery Specifications
BCI Group Size 55
1.
2.
3.
4.
Battery
5.
6.
7.
8.
Carriage screw
Battery tray
Retainer
Negative battery cable
Positive battery cable
Fusible link
585
CCA at 0oF (--18oC)
Reserve Capacity of 95 minutes at 80oF (27oC)
Flange nut
Dimensions (including terminal posts)
Length
Width
Height
8.3 inches (211 mm)
6.0 inches (152 mm)
8.5 inches (216 mm)
B. Checkbatteryterminalsforcorrosion.Ifcorrosion
occurs at terminals, disconnect cables. Always dis-
connect negative (--) cable first. Clean cable clamps
and battery terminals separately. Reconnect cables
with positive (+) cable first. Coat battery posts and
cable connectors with Battery Terminal Protector
(Toro Part No. 107--0392) or petroleum jelly to pre-
vent corrosion.
Battery Removal and Installation (Fig. 57)
1.
2.
Raise and support hood.
Loosen and remove negative (--) cable from battery.
After negative (--) cable is removed, loosen and remove
positive (+) cable.
IMPORTANT: Before cleaning the battery, tape
or block vent holes to the filler caps and make
sure the caps are on tightly.
3.
4.
5.
Loosen flange nut that secures battery retainer.
Carefully remove battery from machine.
C. Check for signs of wetness or leakage on the top
ofthe battery which mightindicate aloose ormissing
filler cap, overcharging, loose terminal post or over-
filling. Also, check battery case for dirt and oil. Clean
the battery with a solution of baking soda and water,
then rinse it with clean water.
Install battery in reverse order making sure to con-
nect and tighten positive (+) cable to battery before con-
necting negative (--) cable.
NOTE: Before connecting the negative (ground) cable
to the battery, connect a digital multimeter (set to DC
Amps) between the negative battery post and the nega-
tive (ground) cable connector. The reading should be
less than 0.1 amp. If the reading is 0.1 amp or more, the
machine’s electrical system should be tested for short
circuits or faulty components and repaired.
D. Check thatthe cover seal is notbroken away.Re-
place the battery if the seal is broken or leaking.
E. Check theelectrolyte levelineachcell.Ifthelevel
is below the tops of the plates in any cell, fill all cells
with distilled water between the minimum and max-
imum fill lines. Charge at 15 to 25 amps for 15 min-
utes to allow sufficient mixing of the electrolyte (see
battery charging in this section).
6.
Lower and secure hood.
Battery Inspection and Maintenance
1.
Perform the following inspections and maintenance:
A. Check battery case for cracks. Replace battery if
cracked or leaking.
Groundsmaster 4300--D
Page 5 -- 45
Electrical System
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Groundsmaster 4300 D |
Download File |
|
Document Type | Catalog |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)