Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

4.
5.
Loosen cap screws from the rear cover.
A.  Gear shafts should be free of rough surfaces and
excessive wear at bushing points and sealing areas.
Scoring, rough surfaces or wear on gear shafts indi-
cates need for replacement.
Remove motor from the vise. Turn motor so that the
shaft end is facing down. Remove cap screws.
6.
motor.
Separate rear cover from body. Lift rear cover from
B.  Gear teeth should be free  of excessive scoring
and wear. Any broken or nicked gear teeth must be
replaced.
7.
Carefully remove body.  Lift body straight up  to re-
move. Make sure  the rear wear plate  remains on the
drive and  idler gear  shafts. Remove  and discard O--
rings from the body. Locate and retrieve dowel pins.
C. Inspect  gear  face  edge for  sharpness.  Sharp
edges of gears will  mill into wear plates and, thus,
must be replaced.
IMPORTANT: Note position of the open and closed
side of the wear plates before removing. Also, iden-
tify wear  plates (front and  rear) with a  marker for
proper assembly.
4.
Inspect wear plates for the following:
A.  Bearingareasshouldnothaveexcessive   wearor
scoring.
IMPORTANT: Mark the relative positions of the gear
teeth and the wear plates so they can be reassem-
bledinthesameposition.Donottouchthegearsur-
faces as residue on hands may be corrosive to gear
finish.
B.  Face of wear plates that are in contact with gears
should be free of wear, roughness or scoring.
C. Thickness of wear plates should be equal.
5.
Inspect front flange  and rear cover  for damage or
wear.
8.
Carefully remove rear  wear plate, idler  gear, drive
gear and front wear plate from the front flange.
9.  Remove and discard back--upgaskets and pressure
seals from wear plates.
1
2
3
4
10.Turn
front flange over, with seal side up.
IMPORTANT: Make  sure to  not  damage the  front
flange counter bore when removing the seals from
the front flange.
11.
Carefully remove  dust seals, retaining ring,  flange
washer and shaft  seal from the front  flange (Fig. 88).
Discard seals.
Figure 88
1.
2.
Dust seal
Retaining ring
3.
4.
Flange washer
Shaft seal
Inspection
1.
Remove  any nicks  and  burrs from  all  parts  with
emery cloth.
3
CAUTION
2
Use eye protection such as goggles when using
compressed air.
2.
pressed air.
Clean all parts with solvent. Dry all parts with com-
1
3.
Inspect drive gears and idler gears for the following
4
(Fig. 89):
Figure 89
1.
2.
Gear shaft spline
Gear shaft
3.
4.
Gear teeth
Gear face edge
Groundsmaster 4300--D
Page 4 -- 97
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website