Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

Main Power and Glow Relays
The  Groundsmaster  electrical  system  includes  two
identical relays for current control. The main power and
glow relays are attached to a frame bracket under  the
hood next to the  hydraulic pump drive shaft (Fig. 36).
Relays can be identified by a tag on the wire harness.
6.  Disconnect voltage and test leads from the relay ter-
minals. Replace relay if necessary.
7.
Secure relay to machine and connect machine wire
harness connector to relay.
8.
Lower and secure hood.
The main power relay is used to provide current to the
TEC controller,  headlights,  power point  and optional
electric equipment.  When the ignition switch  is in the
RUN or START position, the main power relay is ener-
gized.
1
2
The glow relay is used to provide current to the engine
glow plugs when energized by the TEC controller. The
controller controls  and monitors  the operation  of the
glow relay. The glow relay and its circuit wiring should
be tested as a controller output with the Diagnostic Dis-
play before  disconnecting and  testing the  relay (see
Special Tools and Troubleshooting in this chapter).
3
Testing
Figure 36
1.
decks, stop  engine, apply parking  brake and remove
key from ignition switch.
Park  machine  on  a  level  surface,  lower  cutting
1.   Pump drive shaft
2.   Main power relay
3.
Glow relay
2.
3.
ness connector from the relay. Remove relay from ma-
chine for easier testing.
Open hood to gain access to relay.
Locate relay and disconnect the machine wire har-
30
85
86
NOTE:  Prior to taking small resistance readings with a
digital multimeter, short the  meter test leads together.
The meter will display a small resistance value (usually
87
0.5
ohms or less). This resistance is due to the internal
resistance of the meter and test leads. Subtract this val-
ue from from the measured value of the component you
are testing.
86
85
87
4.
Verify coil resistance between terminals 85  and 86
with a multimeter (ohms setting) (Fig.  37). Resistance
should be approximately 72 ohms.
30
5.
Connectmultimeter (ohmssetting) leadstorelayter-
Figure 37
minals 30 and  87. Ground terminal 86 and  apply +12
VDCtoterminal85.Therelayshouldhavecontinuitybe-
tween terminals 30 and 87 as +12 VDC is applied to ter-
minal 85. The relay should not have continuity between
terminals 30 and 87 as +12 VDC is removed from termi-
nal 85.
Groundsmaster 4300--D
Page 5 -- 33
Electrical System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website