Toro 05138SL Rev A Service Manual Groundsmaster 3280 D 3320 Preface Publication

Removal (Figs. 41 and 42)
Park the  machine on  a level surface,  engage the
parkingbrake,lowerthecuttingdeck(orimplement)and
stop  the engine.  Remove  the  key  from the  ignition
switch.
5.  Connect hydraulic hoses to hydraulic  fittings on lift
control valve.
1.
6.  Install fuel tank to machine (see Fuel Tank Installa-
tion in Chapter 3 -- Gasoline Engine or Chapter 4 -- Die-
sel Engine).
2.
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
Read the  General Precautions  for Removing  and
7.  Check hydraulic  fluid level in reservoir  (front axle)
and adjust  as required  (see Traction Unit  Operator’s
Manual).
3.
moval in Chapter 3 --  Gasoline Engine or Chapter 4 --
Diesel Engine).
Remove fuel tank from machine (see Fuel Tank Re-
8.  Follow Hydraulic System Start--up procedures.
9.
Check counterbalance valve adjustment (see Trac-
tion Unit Operator’s Manual).
4.
poses.Cleanhydraulichoseendspriortodisconnecting
the hoses.
Label all  hydraulic connections  for assembly  pur-
4
CAUTION
3
2
1
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil.
2
5.
on lift control valve. Allow hoses to drain into a suitable
container.
Disconnect hose connections from hydraulic fittings
8
5
7
6
6.
to prevent contamination.
Putcaps or plugs on disconnected hoses andfittings
Figure 42
1.
2.
3.
4.
Lift control valve
Hydraulic adapter
Hydraulic tube
5.
6.
7.
8.
Hydraulic fitting
Cap screw (2 used)
Lock washer (2 used)
Flat washer (2 used)
7.
cure link tube (item 20) to control valve.
Removecotterpin(item14)andpin(item13)thatse-
Counterbalance manifold
8.
(item 12) and flat washers (item 10) that secure lift con-
trol valve to machine.
Remove two (2) cap screws (item 11), lock washers
9.
Remove control valve from the machine.
10.Remove
hydraulic  fittings as  necessary  from the
control valve. Discard all removed o--rings.
Installation (Figs. 41 and 42)
1.
Install all removed hydraulic fittings with new o--rings to
the lift control valve.
Coat  new o--rings  lightly with  clean  hydraulic oil.
2.
Position lift control valve to machine frame. Secure
control valve to machine with two (2) cap screws (item
lock washers (item 12) and flat washers (item 10).
11),
3.
Secure link tube (item 20)  to control valve with pin
(item 13) and cotter pin (item 14).
4.
Remove all caps or plugs from hydraulic hoses and
fittings.
Groundsmaster 3280--D/3320
Page 5 -- 55  Rev. A
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 260 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website