Toro 05138SL Rev A Service Manual Groundsmaster 3280 D 3320 Preface Publication

Removal (Fig. 62)
Park machine on a level surface, lower cutting deck
(or implement), stop engine, engage parking brake and
remove key from the ignition switch.
Installation (Fig. 62)
1.
1.  Position rear axle support to axle. Install thrust wash-
ers (items 32 and 33) between axle boss and axle sup-
port to minimize clearance.
2.
Manual).
Drain oil from rear axle (see Traction Unit Operator’s
2.  Install axle pin (item 23)  to secure axle to rear axle
support. Install thrust washer (item 17) and jam nut (item
18)
onto pivot pin. Torque jam nut from  90 to 120 ft−lb
to 163 N−m). Secure pivot pin to axle support with
washer head screw (item 24).
(122
CAUTION
3.
jack.  Raise  assembly  to   machine  frame  and  align
mounting holes of axle support and machine frame.
Position axle and axle support under machine with a
When changing attachments, tires, or perform-
ing other  service, use correct  blocks, hoists,
and jacks. Make  sure machine is parked on  a
solid, level  surface such  as a concrete  floor.
Prior to  raising machine,  remove any attach-
ments  that  may  interfere  with  the safe  and
proper raising of the machine. Always chock or
block wheels.  Use jack stands  or solid wood
blocks to support the raised machine. If the ma-
chine is  not properly supported  by blocks or
jack  stands, the  machine  may  move  or fall,
which may result in personal injury.
4.
head screws (item 20) and two (2) cap screws (item 26)
with lock nuts (item 21).
Secure rear axle support to frame with four (4) flange
5.
ing Cylinder Installation in Service and Repairs section
of Chapter 5 − Hydraulic System).
Install steering cylinder to axle assembly (see Steer-
6.  Position end of  driveshaft to bidirectional clutch on
rear axle. Secure driveshaft to clutch with six (6) socket
head screws (item 10) and lock washers (item 9).
3.
Chock front wheels and jack up rear of machine (see
Jacking Instructions in Chapter 1 − Safety). Support ma-
chine with jack stands or solid wood blocks.
WARNING
4.
Remove wheels from rear axle.
Failure  to   maintain  proper  wheel   lug  nut
torque could result in failure or loss of wheel
and may result in personal injury.
5.
Remove six (6)  socket head screws  (item 10) and
lock washers (item 9) that secure driveshaft to bidirec-
tional  clutch on  rear axle.  Position  end of  driveshaft
away from clutch.
7.
Install wheels to axle. Torque wheel lug nuts from 70
6.
Remove steering cylinder from rear axle (see Steer-
to 90 ft−lb (95 to 122 N−m).
ing Cylinder Removal in Service and Repairs section of
Chapter 5 − Hydraulic System).
8.
9.
Lower machine to ground.
If equipped with  rear weight(s), attach weight(s)  to
7.
If machine has rear weight(s) attached to frame, re-
rear of machine.
move weight(s).
10.Fill
gear lube (see Traction Unit Operator’s Manual).
axle and input gearbox with SAE 80W−90 weight
8.
Support rear axle to prevent it from falling. Remove
two (2) cap screws (item 26) with lock nuts (item 21) and
then four (4) flange head screws (item  20) that secure
rear axle support to equipment frame. Lower rear  axle
and rear axle support from machine.
11.
Start engine and check for component interference
as steering wheel is turned from lock to lock.
12.Check
Traction Unit Operator’s Manual).
rear wheel toe−in and adjust if necessary (see
9.
17)
Remove jam nut (item  18) and thrust washer (item
from axle pin (item 23) that attaches rear axle to rear
axle support. Remove washer head screw (item 24) that
secures flange of axle pin to rear axle support.
13.Check
steering stop bolt adjustment on both sides of
axle. At full RH and LH turns, a gap of 0.088” (2.2 mm)
should exist between bevel gear case casting and stop
bolt on axle case.
10.Remove
axle pin. Separate  rear axle support from
rear axle. Note location of thrust washers on both ends
of axle mounting boss.
Groundsmaster 3280−D/3320
Page 8 − 35 Rev. A
Drive Axles
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 260 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website