Toro 05138SL Rev A Service Manual Groundsmaster 3280 D 3320 Preface Publication

5.
Determine necessary quantity of support shims.
4
57 to 67 ft−lb
(77 to 91 N−m)
A.  Lubricate the axle  case support bushing with  a
thin coat of grease and slide axle case support onto
knuckle pin.
1
B.  Position support shims that were removed during
disassembly between  axle case  support and  axle
case. Install mounting screws into axle case. Slowly
tighten screws  while frequently checking for  clear-
ance (vertical endplay)  between axle case support
and knuckle pin. If  binding of components is noted
before screws are fully tightened, add additional sup-
port shims. Torque screws from 57 to 67 ft−lb (77 to
VERTICAL
ENDPLAY
6
5
2
3
91
N−m).
Figure 70
4.
5.
6.
C. Use dial indicator to measure vertical endplay of
axle case (Fig. 70).
1.
2.
3.
Axle case support
Axle case
Bevel gearcase
Dial indicator
Knuckle pin
Support shim location
AXLE CASE ASSEMBLY ENDPLAY:
0.001
to 0.008 in. (0.02 to 0.20 mm)
3
2
D. Adjust endplay by increasing or reducing number
of axle case support shims.
1
NOTE:  Axle case  support  shims are  available  in
4
0.004
in. (0.10 mm), 0.008 in. (0.20 mm) and 0.016
in. (0.40 mm) thickness.
6.
After correct support shims have been determined,
remove  mounting  screws  and apply  heavy  strength
thread−locking compound  to screw threads.  Reinstall
screws and torque from 57 to 67 ft−lb (77 to 91 N−m).
5
IMPORTANT: Correct  engagement  between  bevel
gears is critical to axle performance and durability.
7.
Temporarily install the bevel gear case/axle case as-
Figure 71
sembly on the axle support. Position a dial indicator at
the tooths  center.  Prevent the  axle from  turning  and
measure the upper bevel gear to differential shaft gear
backlash (Fig. 71).
1.
2.
3.
Axle support
Upper bevel gear
Differential shaft gear
4.
5.
Dial indicator
Axle bearing shims
UPPER BEVEL GEAR BACKLASH:
4
5
0.004
to 0.016 in. (0.10 to 0.40 mm)
1
8.
Adjust backlash by increasing or reducing axle bear-
ing shim thickness (see Differential Shafts in this section
of this manual).
NOTE:  Axle bearing  shims are  available in 0.004  in.
(0.10
mm), 0.008 in. (0.20 mm) and 0.020 in. (0.50 mm)
thickness.
3
2
Figure 72
1.
2.
3.
Axle cover assembly
Lower bevel gear
Axle gear
4.
5.
Dial indicator
Axle bearing shims
Groundsmaster 3280−D/3320
Page 8 − 39
Drive Axles
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 260 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website