Toro 05138SL Rev A Service Manual Groundsmaster 3280 D 3320 Preface Publication

Removal (Fig. 39)
Park the  machine on  a level surface,  engage the
parkingbrake,lowerthecuttingdeck(orimplement)and
stop  the engine.  Remove  the  key  from the  ignition
switch.
Installation (Fig. 39)
1.
1.  Coatnewo--ringslightly  withcleanhydraulicoil.Ifre-
moved, install hydraulic fittings with new o--rings to the
steering cylinder. Make sure to position fittings correctly
in cylinder.
2.
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
Read the  General Precautions  for Removing  and
2.  If removed, install ball joints to steering cylinder.
3.
Position steering cylinder to rear axle. Secure cylin-
dertoaxlewithjamnuts.Installfirstjamnutontocylinder
balljointthreadsandtorquefrom70to90ft--lb(95to122
N--m). Then, while retaining  first jam nut with wrench,
install and torque second jam nut from 70 to 90 ft--lb (95
to 122 N--m).
CAUTION
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil.
4.
fittings.
Remove caps and plugs from  hydraulic hoses and
5.
der.
Correctly connect hydraulic hoses to steering cylin-
3.
Label all  hydraulic connections  for assembly  pur-
poses.Cleanhydraulichoseendspriortodisconnecting
the hoses.
6.  Check hydraulic  fluid level in reservoir  (front axle)
and adjust  as required  (see Traction Unit  Operator’s
Manual).
4.
5.
Disconnect hydraulic hoses from steering cylinder.
Putcaps or plugs on disconnected hoses andfittings
7.  Lubricate cylinder grease fittings (see Traction Unit
Operator’s Manual).
to prevent contamination.
6.
der to machine.
Remove four (4) jam nuts that secure steering cylin-
8.  Follow Hydraulic System Start--up procedures.
9.
Check that  steering cylinder  does not contact  the
axle or frame as cylinder moves from fully retracted to
fully extended.
7.
Remove steering cylinder with ball joints from machine.
Separate steering cylinder ball joints from rear axle.
8.
9.
quired. Note orientation of fittings before removing from
steering cylinder.
If needed, remove ball joints from steering cylinder.
Removehydraulic fittingsfromsteeringcylinder  ifre-
Groundsmaster 3280--D/3320
Page 5 -- 51
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 260 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website