Toro 05138SL Rev A Service Manual Groundsmaster 3280 D 3320 Preface Publication

Rear Wheel Bearings (2 Wheel Drive)
NOTE:  For repair information  regarding the rear  axle
on 4 wheel drive machines, refer  to Chapter 8 − Drive
Axles.
4.  Slide the wheel hub assembly onto the spindle shaft
and secure it in place with the tab washer and jam nut.
DO NOT tighten the nut or install the cotter pin.
Disassembly (Fig. 7)
5.  Rotate the wheel hub by hand and tighten the jam nut
from 75 to 100 in-lb (8.5 to 11.3 N−m) to set the bearings.
Then, loosen the nut until the hub has endplay.
1.
Jack up the rear of the machine until the tire is off the
floor. Support the machine with jack stands or blocks to
prevent it from falling.
6.  Rotate the wheel hub by hand and tighten the jam nut
from 15 to 20 in-lb (1.7 to 2.3 N−m). After final tightening,
make sure that the  wheel hub does not have any  free
play.
2.
3.
4.
Remove the rear wheel (see Wheels in this section).
Remove the dust cap from the wheel hub.
7.
Install retainer with slot aligned to cotter pin hole  in
Remove  the cotter  pin,  retainer, jam  nut  and tab
spindle. Install cotter pin.
washer. Slide the wheel hub from the spindle shaft.
8.
9.
Install dust cap.
5.
Pull the seal out of the wheel hub. Discard seal.
Install rear wheel (see Wheels in this section).
6.
Remove the  bearing cones from  both sides of  the
wheel hub. Clean the bearings in solvent. Make sure the
bearings are in good operating condition. Clean the in-
side of the wheel hub. Check the bearing cups for wear,
pitting or  other  noticeable damage.  Replace worn  or
damaged parts.
10.Remove
floor.
jack stands or blocks and lower machine to
6
8
Assembly (Fig. 7)
7
1.
press them into the hub until they seat against the shoul-
der of the hub.
If bearing cups were  removed from the wheel hub,
6
9
5
4
2
IMPORTANT: The  seal must be  pressed in so  it is
flush with the end  of the wheel hub. The  lip of the
seal must be toward the bearing.
1
3
2.
Pack both bearings with grease. Install one bearing
into the cup on inboard side of the wheel hub. Lubricate
the inside of the new seal and press it into the wheel hub.
Figure 7
1.
2.
3.
4.
5.
Dust cap
Cotter pin
Retainer
Jam nut
Tab washer
6.
7.
8.
9.
Bearing cone
Bearing cup (2 used)
Wheel hub
3.
Pack inside of wheel hub with some grease (not full).
Position remaining bearing into the outer bearing cup.
Seal
Groundsmaster 3280−D/3320
Page 7 − 15
Chassis
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 260 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website