Toro 05138SL Rev A Service Manual Groundsmaster 3280 D 3320 Preface Publication

Blade Spindle Service
Disassembly (Fig. 4)
2
1
1.
Loosen  and remove  lock  nut from  top  of spindle
shaft.
3
4
NOTE:  Early production spindle assemblies included a
v−ring seal (item 4) which has been found to be unnec-
essary. Discard v−ring seal if found in spindle assembly.
130 to 150 ft−lb
(176 to 203 N−m)
5
2.
Remove flat washer and pulley from shaft. If spindle
6
is equipped with a v−ring seal, remove and discard  v−
ring seal.
8
7
9
3.
Remove the spindle shaft from the spindle housing
which may require the use of an arbor press. The spindle
shaft spacer should remain on the spindle shaft as the
shaft is being removed.
10
6
4.
5.
Remove oil seals from spindle housing.
11
12
Allow the bearing cones,  inner bearing spacer and
spacer ring to drop out of the spindle housing.
6.
cups out of the spindle housing. Remove the outer bear-
ing spacer from the housing.
Using a punch and hammer, drive both of the bearing
Figure 4
1.
2.
3.
4.
5.
6.
Lock nut
Flat washer
Pulley
7.
8.
9.
Bearing set
Spacer set
Spindle housing
10. Grease fitting
11.  Shaft spacer
12. Spindle shaft
V−ring seal (if equipped)
O−ring
7.
housing. Removal of this snap ring is very difficult.
The large  snap ring can  remain inside the  spindle
Oil seal
Assembly (Fig. 4)
1
2
NOTE:  A replacement spindle bearing set contains two
(2)
bearings, a spacer ring and a large snap ring (Fig. 5).
4
These parts cannot be purchased separately. A replace-
ment spacer  set includes  the inner  spacer and  outer
spacer.
IMPORTANT: If  new  bearings  are installed  into  a
used spindle housing, it may not be necessary to re-
place  the original  large  snap ring.  If  the original
snap ring is in good condition with no evidence  of
damage (e.g. spun bearing), leave the  snap ring in
the housing and discard  the snap ring that comes
with the new bearings. If the large snap ring is found
to be damaged, replace the snap ring. Replacement
bearings are sold only with a  matched spacer ring
and large snap ring (Fig. 5). These parts cannot be
purchased separately.
5
3
1
Figure 5
1.
2.
3.
Bearing
4.
5.
Inner spacer
Outer spacer
Spacer ring
Large snap ring
1.
If large snap ring was removed from spindle housing,
install snap ring into  housing groove. Make sure snap
ring is fully seated in housing groove.
2.
Install outer bearing spacer into top of spindle hous-
ing. The spacer should fit against the snap ring.
Cutting Units
Page 10 − 10   Rev. A
Groundsmaster 3280−D/3320
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 260 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website