Toro 03116SL Rev E Service Manual Groundsmaster 4100 D Preface Publication

Rear Axle Assembly
18
17
16
2
3
RIGHT
70
(94
ft−lb maximum
N−m maximum)
FRONT
19
7
15
14
13
12
5
11
10
4
9
8
6
1
Figure 8
1.
2.
3.
4.
5.
6.
7.
Frame
Cap screw (6 used)
Flat washer
Bulkhead lock nut (2 used)
Washer
Thrust washer (thick)
Grease fitting (2 used)
8.
9.
10. Washer head screw
11.  Pivot pin
12. Rear frame mount
13. Washer
Rear axle assembly
Thrust washer (thin)
14. Lock nut
15. Flange nut
16. Rear bumper
17. Hydraulic manifold (4WD)
18. Cap screw (2 used)
19. Flange nut
Remove Rear Axle
Park machine on a level surface, lower cutting units,
2.  Chock front wheels and jack up rear of machine (see
Jacking Instructions in Chapter 1 − Safety). Support ma-
chine with jack stands or solid wood blocks.
1.
stop engine,  engage parking  brake, and  remove key
from the ignition switch.
3.  Drain oil from rear axle and axle gearbox (see Oper-
ator’s Manual).
CAUTION
4.
Remove wheels from rear axle.
5.
(see Rear Axle Motor in Service and Repairs section of
Chapter 4 − Hydraulic System).
Remove hydraulic  motor from  rear axle  assembly
When changing attachments, tires, or perform-
ing other  service, use correct  blocks, hoists,
and jacks. Make  sure machine is parked on  a
solid, level  surface such  as a concrete  floor.
Prior to  raising machine,  remove any attach-
ments  that  may  interfere  with  the safe  and
proper raising of the machine. Always chock or
block wheels.  Use jack stands  or solid wood
blocks to support the raised machine. If the ma-
chine is  not properly supported  by blocks or
jack  stands, the  machine  may  move  or fall,
which may result in personal injury.
6.
ing Cylinder in Service and Repairs section of Chapter
Remove steering cylinder from rear axle (see Steer-
4
− Hydraulic System).
7.
Disconnect both  steering cylinder  hydraulic hoses
from hydraulic tubes at rear  frame mount (Fig. 9). Re-
move bulkhead locknuts and washers that secure steer-
ing  cylinder   hydraulic  tubes  to   rear  frame  mount.
Separate tubes from frame mount.
Axles, Planetaries, and Brakes
Page 6 − 12
Groundsmaster 4100−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 258 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website