General Safety Instructions
The GROUNDSMASTER 4100-D was tested and certi-
fied by TORO for compliance with existing safety stan-
dards and specifications. Although hazard control and
accident prevention partially are dependent upon the
design and configuration of the machine, these factors
are also dependent upon the awareness, concern, and
proper training of the personnel involved in the opera-
tion, transport, maintenance, and storage of the ma-
chine. Improper use or maintenance of the machine can
result in injury or death. To reduce the potential for injury
or death, comply with the following safety instructions.
WARNING
To reduce the potential for injury or death,
comply with the following safety instructions.
Before Operating
1.
Read and understand the contents of the Operator’s
3. Assure interlock switches are adjusted correctly so
engine cannot be started unless traction pedal is in
NEUTRAL and cutting unit is DISENGAGED.
Manual before starting and operating the machine. Be-
come familiar with the controls and know how to stop the
machine and engine quickly. A replacement Operator’s
Manual is available on the Internet at www.Toro.com or
by sending the complete model and serial number to:
4.
Since diesel fuel is highly flammable, handle it care-
fully:
A. Use an approved fuel container.
The Toro Company
Attn. Technical Publications
B. Do not remove fuel tank cap while engine is hot or
running.
8111
Lyndale Avenue South
Bloomington, Minnesota 55420−1196
C. Do not smoke while handling fuel.
2.
Keep all shields, safety devices, and decals in place.
If a shield, safety device, or decal is defective, illegible
or damaged, repair or replace it before operating the
machine. Also tighten any loose nuts, bolts or screws to
ensure machine is in safe operating condition.
D. Fill fuel tank outdoors and only to within an inch of
the top of the tank, not the filler neck. Do not overfill.
E. Wipe up any spilled fuel.
While Operating
1.
chine.
Sit on the seat when starting and operating the ma-
5. Before getting off the seat:
A. Ensure that traction pedal is in neutral.
B. Set parking brake.
2.
Before starting the engine:
A. Engage the parking brake.
C. Disengage cutting unit and wait for blades to
stop.
B. Make sure traction pedal is in neutral and the
PTO switch is OFF (disengaged).
D. Stop engine and remove key from switch.
C. After engine is started, release parking brake and
keep foot off traction pedal. Machine must not move.
If movement is evident, the traction pedal linkage is
adjusted incorrectly; therefore, shut engine off and
adjust linkage until machine does not move when
traction pedal is released.
E. Toro recommends that anytime the machine is
parked (short or long term), the cutting unit should be
lowered to the ground. This relieves pressure from
the lift circuit and eliminates the risk of the cutting unit
accidentally lowering to the ground.
F. Do not park on slopes unless wheels are chocked
or blocked.
3.
quate ventilation. Exhaust fumes are hazardous and
could possibly be deadly.
Do not run engine in a confined area without ade-
4.
Do not touch engine, muffler or exhaust pipe while
engine is running or soon after it is stopped. These areas
could be hot enough to cause burns.
Safety
Groundsmaster 4100−D
Page 1 − 2
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Groundsmaster 4100 D |
Download File |
|
Document Type | Catalog |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)