Toro 03116SL Rev E Service Manual Groundsmaster 4100 D Preface Publication

Flush Hydraulic System
IMPORTANT: Flush the hydraulic  system any time
there is a severe component failure or the system is
contaminated (oil appears milky, black, or contains
metal particles).
6.  Reconnect all hydraulic  hoses, tubes, and compo-
nents that were disconnected while draining system.
NOTE:  Useonly hydraulic fluids specifiedintheOpera-
tor’s Manual. Other fluids may cause system damage.
IMPORTANT: Flush hydraulic system when chang-
Ing from petroleum base hydraulic fluid to a biode-
gradable fluid  such  as Mobil  EAL 224H.  Operate
machine under normal operating conditions  for at
least four (4) hours before draining.
7.
Operator’s Manual).
Fill hydraulic reservoir with new hydraulic fluid (see
8.
lenoid.
Disconnect electrical connector from engine run so-
1.
decks,stopengine,andengageparkingbrake.Remove
key from the ignition switch.
Park  machine  on a  level  surface.  Lower  cutting
9.
onds to prime hydraulic pumps. Wait 15 seconds to al-
low the starter to cool and then repeat this step again.
Turn ignition key switch; engage starter for 15 sec-
10.Connect
electrical connector to engine run solenoid.
CAUTION
11.
Startengineandletitrunatlowidle     (1375 + 50RPM)
for a minimum of 2 minutes. Increase engine speed to
high idle (2730 + 30 RPM) for aminimum of1minuteun-
der no load.
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil. Controls  must be operated with the
ignition switch inOFF.Remove key from the igni-
tion switch.
12.Raise
and lower cutting  decks several times. Turn
steering wheel fully left and right several times.
IMPORTANT: Make  sure to  clean  around any  hy-
draulic connections  that will be  disconnected for
draining.
13.Shut
Check oil level  in hydraulic reservoir  and add correct
amount of oil if necessary.
off engine  and check  for hydraulic oil  leaks.
2.
Drain hydraulic reservoir (see Operator’s Manual).
14.Operate
conditions.
machinefor2hoursundernormaloperating
3.
Drain hydraulic system. Drain all hoses, tubes, and
components while the system is warm.
Change and  replace both hydraulic  oil filters  (see
15.Check
condition  of hydraulic  oil.  If the  new  fluid
shows  any  signs  of  contamination,  repeat  steps  1
through 14 again until oil is clean. If changing to biode-
gradable fluid, repeat steps 1 through 14 again at least
once and until the oil is clean.
4.
Operator’s Manual).
5.
Inspect and clean hydraulic reservoir (see Hydraulic
Reservoir Inspection in the Service and Repairs section
of this chapter).
16.Assume
maintenance intervals.
normal operation and follow recommended
Hydraulic System
Page 4 -- 50
Groundsmaster 4100--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 258 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website