Toro 03116SL Rev E Service Manual Groundsmaster 4100 D Preface Publication

Removal (Fig. 1)
Position machine  on a clean,  level surface. Lower
1.
cutting deck, stop  engine, engage parking brake,  and
remove key from the ignition switch.
2
NOTE:  Removal of clevis pins from deck  and height−
1
of−cut chains is easier if deck is lifted slightly.
2.
Remove  hairpins and  clevis  pins that  secure  the
height−of−cut chains to the rear of the cutting deck (Fig.
2).
3.
Remove  hydraulic motors  from  cutting deck  (see
Figure 2
Cutting Deck Motor Removal in the Service and Repairs
Section of Chapter 4 − Hydraulic Systems). Position mo-
tors away from cutting deck.
1.
Hairpin and clevis pin
2.
Height−of−cut chain
1
4.
Remove hairpins and clevis pins that secure damp-
ers to lift arms (Fig. 3). Rotate dampers and place on cut-
ting deck.
2
5.
Remove wing  deck lift cylinders  from cutting  deck
(Fig. 4):
4
A.  Remove deck covers as needed to allow access
to lift cylinder fasteners.
3
B.  Remove cap screw and lock nut that secure the
lift cylinder clevis to the wing deck.
C. Remove  flange nut and flat washer from the  ta-
pered stud on the barrel end of the lift cylinder.
Figure 3
1.
2.
Lift arm
Castor arm
3.
4.
Support hub
Damper
D. Remove lift cylinder from the deck. Locate and re-
trieve spacers from each side of the lift cylinder cle-
vis.
6
6.
Disconnect cutting deck wire harness from main ma-
1
chine harness (Fig. 5).
5
4
7.
Remove cap screws, flat  washers, and flange nuts
that secure  support hubs to  cutting deck castor  arms
(Fig. 3).
160 to 180 ft−lb
3
(217
to 244 N−m)
2
8.
Slide the cutting deck away from the traction unit.
Installation (Fig. 1)
Position machine on a clean, level surface. Lower lift
1.
arms, stop engine, engage parking brake, and remove
key from the ignition switch.
2.
Position the cutting deck to the lift arms.
Figure 4
3.
cure with cap screws, flat washers, and flange nuts (Fig.
3).
Align support hub to cutting deck castor arms and se-
1.
2.
3.
Wing deck lift cylinder
Flat washer
Flange nut
4.
5.
6.
Lock nut
Cap screw
Spacer
Groundsmaster 4100−D
Page 8 − 7
Cutting Deck
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 258 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website