Toro 03116SL Rev E Service Manual Groundsmaster 4100 D Preface Publication

Blade Spindle Service
DRIVEN SPINDLE
7
8
1
2
3
9
10
12
11
14
4
130
(176
to 150 ft−lb
to 203 N−m)
13
17
15
DRIVE SPINDLE
1
5
2
4
9
8
16
17
6
17
Figure 15
1.
2.
3.
4.
5.
6.
Lock nut
Flat washer
Driven pulley
V−ring seal (if equipped)
Drive pulley (single shown)
Hydraulic motor mount
7.
8.
9.
10.  Outer bearing spacer
11.  Inner bearing spacer
12.  Spacer ring
O−ring
Oil seal
Bearing cup and cone
13.  Snap ring
14.  Grease fitting
15.  Spindle housing
16.  Spindle shaft spacer
17.  Spindle shaft
Disassembly (Fig. 15)
6.  The large  snap ring can  remain inside the  spindle
housing. Removal of this snap ring is very difficult.
NOTE:  Early production spindle assemblies included a
v−ring seal (item 4) which has been found to be unnec-
essary. Discard v−ring seal if found in spindle assembly.
Assembly (Fig. 15)
IMPORTANT: If  new  bearings  are installed  into  a
used spindle housing, it may not be necessary to re-
place  the original  large  snap ring.  If  the original
snap ring is in good condition with no evidence  of
damage (e.g. spun bearing), leave the  snap ring in
the housing and discard  the snap ring that comes
with the new bearings. If the large snap ring is found
to be damaged, replace the snap ring. Replacement
bearings are sold only with a  matched spacer ring
and large snap ring (Fig. 17). These parts cannot be
purchased separately.
1.
Loosen  and remove  lock  nut from  top  of spindle
shaft. Remove  flat washer,  pulley, and v−ring  seal (if
equipped) from spindle. For  drive spindle, remove hy-
draulic motor mount.
2.
Remove the spindle shaft from the spindle housing
which may require the use of an arbor press. The spindle
shaft spacer should remain on the spindle shaft as the
shaft is being removed.
3.
Remove oil seals from spindle housing.
1.
spindle housing  groove. Make  sure snap  ring is  fully
seated in housing groove.
If large snap ring was removed, install snap ring into
4.
spacer ring to drop out of the spindle housing.
Allow the bearing cones, inner bearing spacer, and
5.
cups out of the spindle housing. Remove the outer bear-
ing spacer from the housing.
Using a punch and hammer, drive both of the bearing
2.
housing. The spacer should fit against the snap ring.
Install large outer bearing spacer into top of spindle
Cutting Deck
Page 8 − 16  Rev. E
Groundsmaster 4100−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 258 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website