Toro 07150SL Groundsmaster 7200 7210 Service Manual

PTO Drive Shaft Cross and Bearing Service
1.
Drive Shaft Removal in this section).
Remove  PTO drive  shaft  from  vehicle (see  PTO
D. Hold cross in alignment and press bearing in until
it hits the yoke.
IMPORTANT: When   placing  yoke  in  vise,  clamp
lightly on the solid part of the yoke to prevent yoke
damage. Also, the use of a vise with soft jaws is rec-
ommended.
E.  Carefully place  second bearing  into yoke  bore
and onto cross shaft. Press bearing into yoke.
F.  Install snap rings to bearings to secure bearings
in place.
2.
remove snap rings that secure bearings at the inside of
each yoke. Remove yoke from vise.
Lightly clamp yoke in vise. Use two screwdrivers to
G. Repeat procedure for other yoke.
H. Grease cross until grease comes out of all four (4)
bearing cups.
IMPORTANT: Yokes  must  be  supported when  re-
moving and installing bearings to prevent damage.
5.
Make sure that assembled joint moves without bind-
ing. Slight binding  can usually be eliminated by  lightly
rapping the yoke lugs with a soft faced hammer. If bind-
ing continues,  disassemble joint  to identify  source of
binding.
3.
yokes:
Use  a press  to  remove cross  and  bearings from
A.  Place a small socket against one bearing and a
large socket against the yoke on the opposite side.
6.
Install drive  shaft to vehicle  (see PTO Drive  Shaft
B.  While supporting  the large  socket, apply  pres-
sure on small  socket to partially push the  opposite
bearing into the large socket.
Installation in this section).
4
C. Remove   yoke  from  press,  grasp  partially  re-
moved bearing  and tap  on yoke to  completely re-
move the bearing.
3
D. Repeat process for remaining bearings.
E.  Thoroughly clean and inspect all components.
To install new cross and bearings:
1
4.
A.  Apply a coating of grease to bearing bores of end
yoke and shaft yoke. Also, apply grease to bearings
and seal  of  bearing assembly.  Make sure  that all
bearing rollers are properly seated in bearing cage.
2
3
B.  Press one bearing partially into yoke.
Figure 20
IMPORTANT: Take  care when installing  cross into
bearing to avoid damaging bearing seal.
1.
2.
End yoke
3.
Snap ring (4 used)
Shaft yoke
Cross and bearing kit
4.
C. Carefully insert cross into bearing and yoke.
Chassis
Page 6 – 20
Groundsmaster 7200/7210
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 226 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “Toro 07150SL Groundsmaster 7200 7210 Service Manual

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website