Toro 07150SL Groundsmaster 7200 7210 Service Manual

The  Implement Relief  Pressure  Test  should be  per-
formed if a cutting deck (or implement) raise and lower
problem is identified. This test will determine if the imple-
ment relief valve is operating correctly.
11.System pressure should be approximately 3000 PSI
(207 bar) as the implement relief  valve lifts. Return lift
lever to the neutral position.
12.Stop
engine. Record test results.
Procedure for Implement Relief Pressure Test:
13.If
specification is not  met, repair or replace  imple-
1.
perature.
Make sure hydraulic oil is at normal operating  tem-
ment relief valve in gear pump (see Gear Pump Service
in the Service and Repairs section of this chapter). Also
consider a  leaking lift  cylinder, a damaged  lift control
valve or a worn gear pump.
2.
the neutral position.
Make sure that traction drive is correctly adjusted for
14.Relieve
hydraulic system  pressure  (see Relieving
Hydraulic System Pressure in the General Information
section). Disconnect T–connector with test gauge from
lift control valve  fitting and hydraulic hose.  Reconnect
hydraulic hose to control valve fitting.
WARNING
Before disconnecting or performing any work  on
the hydraulic system,  all pressure in  the system
must be relieved. See Relieving Hydraulic System
Pressure in the General Information section.
1
3.
Park machine on a level surface with the cutting deck
(or implement) lowered and off. Make sure engine is off
and the parking brake is engaged.
4.
Read Precautions for Hydraulic Testing listed at the
beginning of this section.
2
5.
er fitting on rear of lift control valve (Fig. 22).
Thoroughly clean junction of hydraulic hose and low-
6.
Disconnect hydraulic hose from lower fitting on rear
of lift control valve (Fig. 22). This hose is from the gear
pump outlet and provides oil flow to the lift control valve
(Fig. 23).
Figure 22
1.
Lift control valve
2.
Hose from gear pump
NOTE:  Implement relief  pressure can also  be tested
with hydraulic tester (pressure and flow). Connect tester
in series with the lift control valve fitting and the discon-
nected hose. Use pressure gauges on hydraulic tester
and follow procedure below.
RIGHT
FRONT
7.
(5000
Install T–connector  with hydraulic  pressure gauge
PSI / 345 bar) in series with the lift control valve
fitting and the disconnected hose.
2
8.
Start engine and run at low idle speed (1500 to 1650
RPM). Check for any hydraulic  leakage from test con-
nections and correct before proceeding with test.
9.
(3200
With  engine  running,  move throttle  to  full  speed
RPM).
1
IMPORTANT: Hold  lift  lever  in  the  raise  position
only long enough to get a system pressure reading.
Holding the lift lever in the raise position for an ex-
tended period may damage the lift control valve.
Figure 23
1.
Gear pump
2.
Hose to lift control valve
10.Watch
pressure gauge carefully while moving lift le-
ver to the raise position and holding.
Groundsmaster 7200/7210
Page 4 – 37
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 226 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “Toro 07150SL Groundsmaster 7200 7210 Service Manual

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website