Blade Spindle Service
Disassembly (Fig. 10)
1
2
1.
Remove lock nut from top of spindle shaft.
NOTE: Early production spindle assemblies included a
v–ring seal (item 4) which has been found to be unnec-
essary. Discard v–ring seal if found in spindle assembly.
3
4
130
(176
to 150 ft–lb
to 203 N–m)
2.
shaft. If spindle is equipped with a v–ring seal, remove
and discard v–ring seal.
Remove special hardened washer and pulley from
5
6
3.
Remove the spindle shaft from the spindle housing
8
which may require the use of an arbor press. The spindle
shaft spacer should remain on the spindle shaft as the
shaft is being removed.
7
9
10
4.
5.
Remove oil seals from spindle housing.
Remove the bearing cones, O–ring, inner bearing
6
spacer and spacer ring from the spindle housing.
11
6.
cups and the outer bearing spacer from the housing.
Using an arbor press, remove both of the bearing
12
7.
housing. Removal of this snap ring is very difficult.
The large snap ring can remain inside the spindle
Figure 10
1.
Lock nut
Special hardened washer
Pulley
V–ring seal (if equipped)
O–ring
Oil seal
7.
8.
9.
10. Grease fitting
11. Shaft spacer
12. Spindle shaft
Bearing set
Spacer set
Spindle housing
Assembly (Fig. 10)
2.
3.
4.
5.
6.
NOTE: A replacement spindle bearing set contains two
(2)
bearings, a spacer ring and a large snap ring (items
1,
2 and 3 in Fig. 11). These parts cannot be purchased
separately. Also, do not mix bearing set components
from one deck spindle to another.
1
NOTE: A replacement bearing spacer set includes the
inner spacer and outer spacer (items 4 and 5 in Fig. 11).
Do not mix bearing spacers from one deck spindle to
another.
4
2
IMPORTANT: If new bearings are installed into a
used spindle housing, it may not be necessary to re-
place the original large snap ring. If the original
snap ring is in good condition with no evidence of
damage (e.g. spun bearing), leave the snap ring in
the housing and discard the snap ring that comes
with the new bearings. If the large snap ring is found
to be damaged, replace the snap ring.
5
3
1
1.
install snap ring into housing groove. Make sure snap
ring is fully seated in housing groove.
If large snap ring was removed from spindle housing,
Figure 11
4.
5.
1.
2.
3.
Bearing
Spacer ring
Large snap ring
Inner spacer
Outer spacer
2.
spacer should fit against the snap ring.
Install outer spacer into top of spindle housing. The
Cutting Deck
Page 7 – 12
Groundsmaster 7200/7210
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 7200, Toro Groundsmaster 7210 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
My mower is a TORO 7210.
Start fuse defection. Why ?