Toro 00062SL Rev I Greensmaster 3250 D Service Manual

9.
blies (27 and 38) away from the hydrostat (45) and se-
cure.
Pull gear pump (28) and connected hoses assem-
10.
Remove hose assemblies (25, 26, and 29) and O--
rings (6 and 16) from the hydraulic fittings (3 and 17). Al-
low hoses to drain into a suitable container.
11.
Remove hydraulic fittings (3 and 17) and O--rings (2
and 20) from the hydrostat (45).
12.
Loosen both set  screws (5) on  the pump hub  (4)
enough to allow the hydrostat (45) shaft to be removed.
CAUTION
SUCTION PORT
Figure 34
Support the  hydrostat when removing  its sup-
porting fasteners to  prevent it from  falling and
causing personal injury.
8.
26,
Install O--rings (6 and 16) and hose assemblies (25,
and 29) to the hydrostat (45) and hydraulic fittings (3
and 17).
13.
Remove both lock nuts (14), cap screws (15), and
flat washers  (19) from  the hydrostat  (45) flange  and
pump plate (46).
IMPORTANT: Failure to remove the plug will cause
excessive pressure  in the  hydrostat and  damage
seals.
14.
Separate hydrostat (45) from  the pump plate (46)
and pump hub (4). Remove key (47) from the hydrostat
shaft.
9.
Remove  plug from  the suction  port  on the  gear
pump (Fig. 34).
Installation (Fig. 30)
10.
Gear Pump Installation).
Install gear pump  to the hydrostat  (see Hydraulic
1.
Apply antiseize lubricant to both the hydrostat (45) shaft
and the inside of the pump hub.
Make sure the inside of the pump hub (4) is clean.
11.
12.
(45).
cablesupporttothehydrostatwithbothcapscrews(Fig.
33).
Remove clamp from pump inlet hose (24).
2.
Coat key (47) with petroleum jelly and insert it into
Position neutral system assembly to the hydrostat
Secure assembly to the hydrostat by securing the
the hydrostat (45) shaft. Position hydrostat to the pump
plate (46) and pump hub (4). Slide the shaft into the hub
with the key.
3.
with both cap screws (15), flat  washers (19), and lock
nuts (14).
Secure the  hydrostat (45) to the  pump plate (46)
13.
the camplate shaft of the hydrostat. Connect extension
spring to the neutral arm (Fig. 32).
Fasten and tighten cap screw and pivot washer to
4.
Apply Loctite #242 (or equivalent) tothreads ofboth
square head screws (5). Install screws (5) in pump hub
to secure hub to pump shaft. Torque screws from 90
to 110 in--lb (10.2 to 12.4 N--m).
14.
spring bracket (Fig. 31).
Connect  extension spring  with  dampener to  the
(4)
15. Check neutral  position of the traction pedal. If ad-
justment is required, see Adjust Transmission for Neu-
tral.
5.
Lubricate all new O--rings with clean hydraulic fluid.
6.
(3
Install new O--rings (2 and 20) and hydraulic fittings
and 17) to the hydrostat.
7.
tings and hydraulic hose connectors. Replace any dam-
aged or worn fittings or connectors.
Inspectthreadsandsealingsurfacesofhydraulicfit-
Hydraulic System (Rev. I)
Page 4 -- 62
Greensmaster 3250--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website