Toro 00062SL Rev I Greensmaster 3250 D Service Manual

5.
Carefully place drive side  plate onto groomer shaft
13.Apply antiseize lubricant to threads of lift arm assem-
bly stud on groomer arm. Install spring washer (item 24)
and lock nut (item 25) to secure drive side groomer arm
assembly to groomer side plate (Fig. 7).
taking care not to damage seals in side plate. Position
side plate to the cutting unit frame and secure with two
shoulder nuts (item 8).
6.
taking care not to get grease on belt surface. Slide drive
pulley onto the reel shaft.
Apply grease to drive pulley splines and pulley hub
14.Center front roller and tighten cap screws (item 20)
to secure roller (Figs. 7 and 8).
15.Install
groomer drive belt and belt cover to side of cut-
7.
Apply anti−seize lubricant to threads of flange head
ting unit  (see Groomer Belt  Replacement in  this sec-
tion).
screw (item 4) used to attach drive pulley to reel shaft.
Secure drive  pulley to  reel with  washer  (item 5)  and
flange head screw.
16.Install
hydraulic reel motor onto cutting unit (see Hy-
draulic Reel  Motor Installation in the  Service and Re-
pairs section of Chapter Chapter 7.1 − Dual Point Adjust
Cutting Units).
8.
install  driven pulley  onto  the  groomer  shaft. Thread
flange nut (item 17) onto the shaft threads.
Place square key (item 31) in groomer shaft slot and
17.If
unit.
equipped, install rotating rear roller brush to cutting
9.
17)
on the other end  of groomer shaft. Torque flange nuts
from 100 to 120 in−lbs. (11.3 to 13.6 N−m).
Secure groomer reel by holding the flange nut (item
on one end of the reel and tightening the flange nut
18.Lubricate
groomer bearings (see Groomer Reel Kit
Installation Instructions).
Note:
After   greasing   groomer   bearings,   operate
10.Apply
Loctite #242 (or equivalent) to threads of cap
groomer for 30 seconds, stop machine and wipe excess
grease from groomer shaft and seals.
plug (item 21). Install cap plug into non−drive side plate
and torque cap  plug from 60 to  80 ft−lbs. (81 to  108
N−m) (Fig. 8).
19.Check
groomer reel height and mower height−of−cut
settings. Adjust as needed.
11.
Insert front roller into non−drive side groomer arm.
12.Position
drive  side  groomer   arm  to  front  roller,
groomer drive side plate and cutting unit frame. Secure
groomer arm to cutting unit with carriage bolt, tab wash-
er and flange nut.
Groomer (DPA Cutting Unit) (Rev. D)
Page 7.2 − 10
Greensmaster 3250−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website