Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Service and Repairs
Hydraulic Reel Motor
IMPORTANT: When  performing  maintenance pro-
cedures on the cutting units, store the cutting unit
reelmotorsinsupport  tubesontheframetoprevent
damage to the  hoses. Do not raise  suspension to
transport position when the reel motors  are in the
holders in  the traction unit  frame. Damage to  the
motors or hoses could result.
Inspection
1.
if necessary (see Reel Removal and Installation in this
chapter of this manual).
Check reel drive coupler splines for wear. Replace
Installation
1.
purpose lithium base grease.
Coat spline shaft ofthe motor with clean No. 2multi-
Removal
1.
Park machine on a clean  and level surface, lower
2.
tor into themotor adapter plateand leaveapproximately
1/2
3.
Install the flange head screws for the reel drive mo-
cutting units completely to the ground, stop engine, en-
gage parking brake, and remove key  from the ignition
switch.
inch (12.7 mm) of threads exposed on each screw.
Install motor by rotating the motor clockwise so the
2.
3.
lic motor to the motor adapter plate. Rotate motor clock-
wise, and remove motor.
Remove basket from carrier frame.
motor flanges clear the flange head screws.
Loosen flange head screws that secure the hydrau-
4.
flanges are encircling the flange head screws. Tighten
flange head screws.
Rotate the motor counterclockwise until the motor
4.
Place protective plastic cap (see Special Tools) into
the hole in the motor adapter plate.
Backlapping (Units without Optional Backlap/Variable Reel Speed Kit)
CAUTION
TOP FACE
REMOVE
BURR
RELIEF ANGLE
Be careful  when backlapping the  reel because
contact with the reel or other moving parts  can
result in personal injury.
FRONT
FACE
FRONT ANGLE
1.
Remove reel motors from the cutting units and cut-
ting units from the lift arms and pull frame (see Cutting
Unit Removal and Installation).
Figure 10
For a better cutting edge, run a file across the
front face of the bedknife when the lapping operation is
completed. This will remove any burrs or rough edges
that may have built up on the cutting edge.
2.
by inserting a piece of 3/8--inch socket extension drive
into the splined reel drive coupling.
Connectthebacklapping  machinetothecuttingunit
Note:
3.
Attach backlap motor or drive to the socket exten-
sion.
4.
in the Toro General Service Training Book, Reel Mower
Basics (part no. 09168SL).
Follow instructions and procedures for backlapping
Dual Point Adjust Cutting Units (Rev. D)
Page 7.1 -- 8   Rev. I
Greensmaster 3250--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website