Adjust Bedknife Parallel to Reel (Single Point Adjust Cutting Units)
1.
remove reel motor from the cutting unit and cutting unit
fromliftarm(seeCutting UnitRemoval andInstallation).
If the cutting unit is not removed from the machine,
C. Should the reel be unable to cut the paper, it will
benecessary toeither backlap orregrind thecutting
unit to achieve the sharp edges needed for preci-
sion cutting. Refer to the Toro General Service
Training Book, Reel Mower Basics (part no.
2.
Position cutting unit on a level surface.
09168SL)
for additional information.
3.
Make sure reel contact is removed by turning the
bedknife adjuster counterclockwise (Fig. 9).
8.
When light contact on the paper is evident at each
end of the bedknife, tighten flange lock nuts to securely
retain the pivot hub (Fig. 10).
4.
Position cutting unit with the front roller up (Fig. 10).
A. On either end of the front side of the reel, insert a
long strip of newspaper between the reel and bed-
knife.
3
1
4
B. While slowly rotating the reel forward, turn bed-
knifeadjuster clockwise, oneclickatatime, untilthe
paper ispinched lightly allthewayacross thereel.A
slight drag should result when the paper is pulled.
This drag should be thesame for theentire length of
the bedknife.
3
2
2
C. If equal adjustment is not obtained for the entire
length of bedknife, proceed to steps 5. through 8.
5.
tab (Fig. 9). Also, loosen both flange lock nuts securing
the pivot hub to the frame (Fig. 10).
Loosen both flange lock nuts secured to the frame
Figure 9
6.
Rotate flangelock nuts,on thetopandbottom ofthe
1.
2.
Adjuster
3.
4.
Flange lock nut
Frame tab
Pivot hub (LH)
frametab,clockwiseorcounterclockwise toraiseorlow-
er the end of the bedbar, as required. Do not loosen the
bottom flange nut tightened against the pivot hub. Tight-
en both flange lock nuts against the frame tab to secure
the adjustment adjustment (Fig. 9).
PINCH
7.
ter the adjustments are accomplished, make sure of the
following (Fig. 10):
Check adjustments by repeating steps 3. and 4. Af-
A. The reel can pinch the paper when inserted from
the front.
B. The reel can cut the paper when inserted at a
right angle. It should be possible to cut the paper
withminimumcontactbetweenthebedknifeandthe
reel blades.
CUT
1
1
Figure 10
1.
Flange lock nut
SPA and 4--Bolt Cutting Units (Rev. A)
Page 7 -- 10 Rev. I
Greensmaster 3250--D
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Greensmaster 3250 D |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)