Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Rear Roller and Height−of−Cut Adjuster Removal and Installation
Note:
Figure  42   shows   the  Rollers   and  Bedbar
Installation (Fig. 42)
Assembly for a Single Point Adjust (SPA) cutting units.
Both  the  SPA  and  4−Bolt  cutting  units a  similar  in
construction. Roller  and Height−of−Cut  (H−O−C) Ad-
juster replacement procedures  are the same for  each
unit.
1.
Place cutting unit on a level working surface.
2.
brackets (21) were  removed, reinstall brackets as  fol-
lows:
If the H−O−C adjusters (35) or H−O−C adjustment
Removal (Fig. 42)
A.  Apply Loctite 242 or equivalent to the threads of
the H−O−C adjusters about 1/4 inch (6 mm) below
the hex.
1.
Position machine on a clean and level surface, low-
er cutting units, stop engine, engage parking brake, and
remove key from the ignition switch.
B.  Place H−O−C adjuster through the holes of the
frame tabs. Screw locking nut onto the adjuster, and
run to the bottom of the frame tab. Make sure adjust-
er is free to rotate with no end play.
2.
To remove the cutting unit, remove reel motor from
the cutting unit and the cutting unit from the lift arm (see
Cutting Unit  Removal  and Installation).  Place cutting
unit on a level working surface.
C. Position  H−O−C adjustment bracket on  the in-
side of the frame.  Screw H−O−C adjuster into the
H−O−C  adjustment  bracket  until  the  top  of  the
bracket is 0.68 inch (18 mm) from the bottom of the
frame tab.
3.
Remove rear roller as follows:
A.  Remove cap screw (19) and lock nut  (11) from
both H−O−C adjustment brackets (21).
B.  Remove height−of−cut  tab (20)  from both  H−
O−C adjustment brackets.
D. Insert carriage screws (41) through the H−O−C
adjustment bracket and frame. Secure bracket and
screw with flat washer (32) and lock nut (32).
C. Tilt back of the cutting unit up, and remove rear
roller (22) from both H−O−C adjustment brackets.
3.   Reinstall rear roller as follows:
4.
ment brackets (21) need removing, remove them as fol-
lows:
If the height−of−cut adjusters (35) or H−O−C adjust-
A.  Tilt back of the cutting unit up, and position rear
roller  shaft  (57) under  each  H−O−C  adjustment
bracket (21). Lower unit and brackets onto the roller
shafts.
A.  Remove lock nut (33), flat washer (32), and car-
riage screw (41) from the H−O−C adjustment brack-
et and frame.
B.  Attach height−of−cut tab (20) to both H−O−C ad-
justment brackets so the tab is below the roller shaft.
B.  Unscrew H−O−C adjuster from the top block of
the H−O−C adjustment bracket.
C. Make sure roller is centered on the cutting unit.
Secure height−of−cut tab to the H−O−C adjustment
bracket with cap screw (19) and lock nut (11).
C. Unscrew  locking nut (34) from  the H−O−C ad-
juster. Slide adjuster from the frame tab.
4.   If  the  H−O−C adjustment  brackets (21)  were re-
moved,  verify  height−of−cut  (see  Adjust  Height−of−
Cut).
5.
Reinstall reel motor to the cutting unit and the cut-
ting unit to lift arm (see Cutting Unit Removal and Instal-
lation).
SPA and 4−Bolt Cutting Units (Rev. A)
Page 7 − 22
Greensmaster 3250−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website