Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Installation (Fig. 58)
Note:
If bearings (12) where  removed, grease seals
(13)
placed as a set.
should be  replaced. Both bearings should  be re-
Press bearing to here.
1.
If  bearings (12)  and  grease seals  (13)  were  re-
moved from the reel shaft (1), install seals and bearings
to the shaft as follows:
1
A.  Pack both bearings with No. 2 multipurpose lithi-
um base grease.
Bearing Surface
B.  Clean bearing surfaces of reel shaft. Apply anti-
seize lubricant to both bearing surfaces (Fig. 60).
Press seal to here.
2
IMPORTANT: Pressing the seal too far onto the reel
shaft will cause the seal to spread, and not allow it
to be tight on the shaft (Fig. 60).
Figure 60
1.
Reel shaft bearing
2.   Reel spider
C. With the lip side of the seal facing the reel spider,
press seal onto each end of the reel shaft (Fig. 60).
4.
Install left bearing housing (10) as follows:
A.  Insert bearing housing (10) into the left sideplate
of the frame over  the bearing (12). Make sure the
grease fitting (9) is facing up.
D. Press  bearing onto  each end of  the reel shaft
(Fig. 60).
IMPORTANT: Do not install the flat wire spring (11)
into the right bearing housing. Damage to the spring
may result as well as increased noise and poor qual-
ity of cut.
B.  Apply Loctite 242 or equivalent to the threads of
the two tapered screws (14).
C. Insert both tapered screws (14) through the side
plate and bearing housing (10). Start tapered nuts
2.
Install right bearing housing (10) as follows:
(8)
onto the screws.
A.  Insert bearing housing  (10) into the  right side-
plate of the frame so that the grease fitting (9) is fac-
ing up.
D. Place flat wire spring (11) into the bearing hous-
ing (10).
5.
both flat washers (4) and cap screws (5).
Reinstall shield rod (2) to the frame. Secure rod with
B.  Apply Loctite 242 or equivalent to the threads of
the two tapered screws (14).
6.
to seat bearings (12). Tighten tapered nuts (8) to secure
housings.
Tap both bearing housings (10) with a soft hammer
C. Insert both tapered screws (14) through the side
plate and bearing housing (10). Start tapered nuts
(8)
onto screws.
7.
Insert drive coupler (32) into end of reel shaft (1) to
D. Place bearing spacer (29) into the bearing hous-
ing (10).
accept hydraulic reel motor. Make sure splines of cou-
pler mesh with those of the drive adapter. Secure cou-
pler with retaining ring (31) (Fig. 58 and 59).
3.
Position reel (1) into the cutting unit frame. Slide end
of reel into bearing housing (10) while keeping the bear-
ing (12) straight.
Greensmaster 3250−D
Page 7 − 35
SPA and 4−Bolt Cutting Units (Rev. A)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website