Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Radiator Removal (Fig. 17)
Park machine on a level surface, lower the cutting
units, stop the  engine, engage parking brake,  and re-
move the key from the ignition switch.
Radiator Installation (Fig. 17)
1.
1.   Secure fan shroud (19) to radiator (4) with four cap
screws (22), lock nuts (28), and flat washers (31).
2.
Slide radiator (4) into  the radiator support (8). Se-
cure radiator to support with  four cap screws (18) and
lock  nuts (9).  Also,  install alternator  guard  (30) with
washer (30) to the radiator support.
CAUTION
3.
Position radiator support (8) to the frame.
DO NOT open radiator cap or drain coolant if the
engine or radiator is hot. Pressurized hot coolant
can escape and cause burns.
A.  Secure  rear radiator  support  tab  and  double
hose clamp (23) to the frame  with cap screw (18),
flat washer (35), and lock nut (9). Secure upper ra-
diator support tab to frame with cap screw (7).
Ethylene−gycol  antifreeze  is   poisonous.  Dis-
pose of it properly or store it in a properly labeled
container away from children and pets.
B.  Secure lower portion of  the radiator support to
the  frame with  cap  screw  (7). Secure  alternator
guard (30) to the frame tab with cap screw (18) and
lock nut (9).
2.
radiator. Open drain petcock (32) on the back of the ra-
diator. Drain radiator completely and close petcock.
Place a suitable container under the front end of the
4.
5.
Connect the following hoses to the radiator:
A.  Radiator hoses (2 and 17) with hose clamps (1).
B. Breather hose (24) with hose clamp (20).
If the  hydraulic oil  cooler was  installed, install  oil
3.
4.
Remove screen (10) from radiator support (8).
If the hydraulic oil cooler is installed, drain hydraulic
reservoir and remove oil cooler (see Engine Removal).
5.
Remove the following hoses from the radiator:
cooler to the radiator (see Engine Removal). Fill the hy-
draulic reservoir (see Check Hydraulic System Fluid in
Chapter 5 − Hydraulic System).
A.  Loosen hose clamp (20) and disconnect breath-
er hose (24).
B.  Loosen hose clamps (1) and disconnect radiator
hoses (2 and 17).
6.
Install screen (10) to radiator support (8).
7.
System).
Fill  radiator (4)  with coolant  (see  Check Cooling
6.
diator support (8) from the frame:
Remove the following fasteners  to remove the ra-
A.  Lock nut (9) and cap screw (18) securing the al-
ternator guard (29) to the frame tab. Cap screw (7)
securing the lower radiator support to the frame.
B.  Cap screw (7) securing the upper radiator sup-
port tab to the frame. Lock nut (9), cap screw (18),
and flat washer (30) securing the rear radiator sup-
port tab and  double hose clamp (23) to  the frame
tab.
7.
Remove the radiator support (8) from the frame and
onto a workbench.
8.
Remove four cap screws (18) and lock nuts (9) se-
curing the radiator (4) to the radiator support (8). Slide
radiator out of the support.
9.
Remove four cap screws  (22), lock nuts (28), and
flat washers (31) securing the fan shroud (19) to the ra-
diator (4). Separate the shroud from the radiator.
Greensmaster 3250−D
Page 3 − 13
Engine
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website