Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Front Roller Removal and Installation
Removal
6
4
1.
Position machine on a clean and level surface, low-
er cutting units, stop engine, engage parking brake, and
remove key from the ignition switch.
7
1
Note:
unit either attached to the lift arm or removed from  the
lift arm. Determine your maintenance needs.
The front roller can be removed with the cutting
2.
If removing the cutting unit, remove reel motor from
3
the cutting unit and the cutting unit from lift arm (see Cut-
ting Unit Removal and Installation). Place cutting unit on
a level working surface.
5
2
3.
Remove cap  screws securing  the roller  shafts to
each front bracket (Fig. 43).
Figure 43
1.
2.
3.
4.
Cap screw
Roller
5.
6.
7.
Carriage screw
Lock nut
Lock nut
Note:
The right front bracket is secured to  the frame
Front bracket
Eccentric (shoulder) bolt
with an eccentric bolt and carriage screw, while the left
front bracket  is secured with a  shoulder bolt and  car-
riage screw (Fig. 43).
4.
On either  end of  the roller, remove  eccentric bolt
(shoulder bolt), carriage screw, and lock nuts securing
the front bracket to the frame (Fig. 43).
5.
Remove the front brackets and roller from the cut-
ting unit. Remove the front brackets from the roller shaft
(Fig. 43).
6.
If the front roller  position is to be changed, the re-
maining front bracket may be removed from the  frame
using step 4.
Installation
1.
Place cutting unit on a level working surface.
Figure 44
2.
Determine desired attitude for cutting unit (see Atti-
tude Adjustment).
4.   Place roller shaft into the front bracket. Slide second
front bracket on the other end of roller. Secure bracket
as in step 3. (Fig. 43).
3.
If both front brackets were removed, position brack-
et as follows (Fig. 43):
5.
threads. Center roller in  the front brackets and secure
into place with the cap screws (Fig. 43).
Apply Loctite  242 or  equivalent to  the cap screw
A.  Insert eccentric bolt (shoulder bolt) through the
top hole on the frame and one of the top holes of the
front bracket so the point on the bracket is at the de-
sired position number on the decal (Fig. 44).
6.   Level  front roller to the reel (see  Adjust and Level
Front Roller to Reel, also see Adjust Attitude).
B.  Screw lock nut onto the eccentric bolt (shoulder
bolt) to hold front bracket in place.
C. Insert carriage screw through the bottom hole of
the frame and front bracket. Secure screw and ec-
centric bolt (shoulder bolt) with lock nuts.
Greensmaster 3250−D
Page 7 − 23
SPA and 4−Bolt Cutting Units (Rev. A)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website