Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Wipe any excess grease from the  inner
grease seals (13) where the reel shaft V−rings (3) make
contact. The V−rings should run dry.
1.
Slide the left hand side plate (6) onto the reel shaft.
Make sure  the reel  shaft threads do  not damage  the
grease seals in the side plate.
2.
Apply a film of No. 2 general purpose grease to the
reel shaft threads  and install the left side  reel bearing
locknut (8).
3.
shaft. Make sure the reel shaft threads do not damage
the grease seals in the side plate.
Slide the  right hand  side plate  (10) onto  the reel
2
1
4.
reel shaft threads and install the right side reel bearing
locknut (8).
Apply a film of No. 2 general purpose grease to the
Figure 23
5.
Mount the frame  assembly (17) to the  side plates
with the  four shoulder  bolts  (7). Torque  the shoulder
bolts to
11.
tor’s Manual for adjustment procedures.
Adjust the cutting unit. See the Cutting Unit Opera-
.
The parallel position of the rear roller to the reel
is controlled by the precision machined components of
the assembled cutting unit. Only a limited amount of ad-
justment is  possible if  necessary due  to tapered  reel
wear. To adjust:
6.
two capscrews (24), washers (23), and lock nuts (25).
Secure the grass shield (22) to the side plates with
7.
8.
Torque the reel bearing locknuts (8) to
.
A.  Place the assembled  cutting unit on  a surface
plate.
Install the bedbar assembly (see Bedbar Installation
in this chapter).
B.  Loosen each  bedbar  adjuster assembly,  both
cap screws (24), and all four shoulder bolts (7).
9.
Install the rear roller as follows (Fig. 23):
A.  On one of the saddle clamps, remove one of the
screws and nuts securing it to the side plate.
C. Adjust  the cutting unit and tighten the shoulder
bolts (7) to a torque of
.
B.  Install rear roller into saddle clamps and loosely
secure  it  with  the screw  and  nut  previously  re-
moved.
D. Tighten the cap screws (24).
E.  Tighten each bedbar adjuster assembly until the
adjuster  spring is  fully  compressed, then  loosen
lock nut 1/2 turn.
C. Center  the roller  between side plates.  Tighten
the saddle clamp screws and nuts to secure the roll-
er.
For severely tapered reels, a .010 in. (.254 mm)
shim (Toro Part No. 106-6923) is available for the  rear
roller mount.
10.
Install the front roller (see Front Roller Installation in
this chapter).
Greensmaster 3250−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website