Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Installation
Note:
New cutting units are shipped with the counter
weight mounted to left end and drive coupler  mounted
in the right end of cutting unit.
3
2
1.
If a cutting  unit is to  be mounted in the  right front
1
position, proceed as follows (Fig. 39):
A.  Remove both flange head screws and lockwash-
ers securing the counter weight to the left end of cut-
ting unit. Remove counter weight.
7
5
4
6
Figure 39
B.  Remove snap ring securing the drive coupler in
the right bearing housing. Remove drive coupler.
1.
2.
3.
4.
Flange head screw
Lock washer
Counter weight
Drive coupler
5.
6.
7.
Left end of reel shaft
Snap ring
Plastic spacer
C. Apply No. 2 multipurpose lithium base grease to
the inside of the drive coupler. Install drive coupler
into the left end of the reel shaft with the snap ring.
5.
Slide sleeve  back on each  ball joint  receiver and
hook onto cutting unit ball studs (Fig. 37).
Note:
104−2067),
grease  into the  bearings  and  reduce the  amount  of
grease used.
On  units  without  plastic  spacers  (Toro   P/N
spacers  can  be  installed  to  help  direct
6.
Mount basket onto carrier frame.
7.
9.5
Adjust pull links until there is 1/4 to 3/8 inch (6.4 to
mm) clearance between the lip of the basket and the
D. Install plastic spacer into the bearing housing.
reel blades. Make sure  the basket lips are equidistant
from the reel blades all the way across the reel blades.
E.  Install counter weight to the right end of the cut-
ting unit with the flange head screws and lockwash-
ers. Move RH end screws to the left end.
8.
Install hydraulic motor to bearing housing as follows
(Fig. 36).
2.
the cutting unit front roller (Fig. 37).
Make sure ball studs are threaded into each end of
A.  Coat spline shaft of the motor with  clean No. 2
multipurpose lithium base grease.
3.
pull frame while hooking the lift roller onto lift arm (Fig.
38).
On the front cutting units, slide cutting unit under the
B.  Assemble the mounting capscrews for  the reel
drive motor to each cutting unit. Leave approximate-
ly 1/2 inch (12.7 mm) of  threads exposed on each
mounting cap screw.
IMPORTANT: Do  not operate  lift system when  the
rear cutting unit is in the service position. Damage
could result to the pull frame and clevis assembly.
C. Install motor by rotating the motor clockwise so
the motor flanges clear the flange head screws.
Note:
When installing  cutting  units with  groom-
D. Rotate the motor counterclockwise until the mo-
tor flanges are  encircling the flange head  screws.
Tighten flange head screws.
ers, and groomer carton  label does not read “with
extension brackets,”  Groomer Extension  Kit, part
no. 99−4255, is required.
E.  Using a hand pump grease gun, fill cavity in the
bearing housing of  cutting unit with No.  2 general
purpose grease.
4.
the service position (Fig. 38).
On the rear cutting unit, rotate and latch unit into into
A.  Lower the suspension system completely (cylin-
ders extended).
B.  Lift the carrier frame by hand until the anti-scalp
rollers clear the brake linkage.
C. Lift up on the slotted link and rotate the pull frame
into the wire hook.
D. With the cutting unit in position, release the wire
hook and rotate the pull frame to operating position.
The slotted link locks automatically.
SPA and 4−Bolt Cutting Units (Rev. A)
Page 7 − 18
Greensmaster 3250−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website