Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Bedbar Removal and Installation
Removal (Fig. 12)
6
1
8
7
1.
Position machine on a clean and level surface, low-
er cutting units, stop engine, engage parking brake, and
remove key from the ignition switch.
2.
Remove  the basket  from  the  cutting unit  carrier
frame.
3.
4.
5.
Disconnect the drive motor from the cutting unit.
Disconnect the cutting unit from the pull link.
Unhook the cutting unit from the lift arm and slide the
cutting unit out from under the carrier frame.
5
4
2
3   4
5
6.
Loosen the two  lock nuts (15) on the  end of each
bedbar adjuster assembly.
Figure 13
1.
2.
3.
4.
Sideplate
5.
6.
7.
8.
Washer (metal)
Bedbar
Bedbar pivot bolt
Flange nut
7.
bolt (7).
Loosen the two flange nuts (8) on each bedbar pivot
Rubber bushing
Flange bushing
Washer (plastic)
8.
the washers (4 and 5) from the outside of the cutting unit
side plates.
Remove the two bedbar pivot bolts (7), and each of
4.
(4)
must contact the flange nut (8) (Fig. 13).
Slide one metal washer (5) and one plastic washer
onto each bedbar pivot  bolt. The metal washer (5)
9.
and 5) from the inside of the cutting unit side plates.
Remove the bedbar (6) and each of the washers (4
5.
Position bedbar (6) into cutting unit. Slide the top of
the bedbar arms between washers on each adjuster as-
sembly.
10.
ry.
Inspect flange bushings (3) and remove if necessa-
Inspect rubber bushings (2) and remove if necessa-
6.
Position one metal washer (5) and one plastic wash-
11.
ry.
er (4) between bedbar and each side  plate. The metal
washer (5) must contact the bedbar (Fig. 13).
Installation (Fig. 12)
7.   Install  the  bedbar pivot  bolt  assemblies.  Tighten
each bedbar pivot bolt from 190 to 240 in−lbs. (21 to 27
Nm).
1.
If either rubber bushing (2)  was removed from the
side plate, install a new bushing. The bushing should be
installed flush with the inside of the side plate (Fig. 13).
8.   Tighten both flange  nuts (8) to remove end play at
the outer washers. Do not over tighten  the flange nuts
or distort the side plates.
2.
Install the flange bushings (3) with flange facing out-
ward.
9.
assembly until the adjuster spring is fully compressed,
then loosen lock nut 1/2 turn.
Tighten the lock nut  (15) on each bedbar adjuster
3.
of each bedbar pivot bolt (7) and  apply antiseize lubri-
cant to the threads of each bedbar pivot bolt (7).
Thread the flange nuts (8) all the way up to the head
10.
Adjust  cutting  unit  (see  Cutting  Unit  Operator’s
Manual).
Greensmaster 3250−D
Page 7.1 − 11
Dual Point Adjust Cutting Units (Rev. D)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website