Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Disassembly
IMPORTANT: Do  not clamp  vise jaws  against the
shaft surface. Protect shaft surface before mount-
ing in a vice.
1.
pumping the cylinder shaft. Plug  both ports and clean
the outside of the cylinder.
Removeoilfromliftcylinderintoadrainpanbyslowly
3.  Mountshaftsecurelyinavisebyclampingonthecle-
vis of the shaft.
IMPORTANT: Prevent  damage when clamping  the
hydraulic cylinder into a vise;  clamp on the clevis
only. Do not close vise enough to distort the barrel.
A.  Coat shaft with with clean hydraulic oil.
B.  Slide head onto the onto the shaft. Install rod seal
onto shaft and into head.
2.
Mount lift cylinder in a vice. Remove internal  collar
with a spanner wrench.
C. Install  piston and nut onto the shaft. Torque nut
3.
Extract shaft, head, and piston by carefully twisting
from 24 to 30 ft--lb (33 to 41 N--m).
and pulling on the shaft.
D. Remove shaft from the vise.
IMPORTANT: Do  not clamp  vise jaws  against the
shaft surface. Protect shaft surface before mount-
ing in a vice.
IMPORTANT: Prevent  damage when clamping  the
hydraulic cylinder into a vise;  clamp on the clevis
only. Do not close vise enough to distort the barrel.
4.
vis of the shaft.  Remove lock nut and piston  from the
shaft. Slide head off the shaft.
Mountshaftsecurelyinavisebyclampingonthecle-
4.
5.
Mount barrel in a vice.
Coat all internal parts with  a light coat of clean hy-
draulic oil. Slide piston, shaft, and head assembly into
the barrel being careful not to damage the seals.
5.
move O--ring,back--upring, rodseal, anddust  sealfrom
the head.
Remove Uni--ring and  O--ring from the piston. Re-
6.
Clean threads of internal collar and threads in cylin-
der barrel. Apply medium strength thread locking com-
pound (e.g. Loctite  #242) to threads of internal collar.
Secure head  in the barrel with  internal collar using  a
spanner wrench. Tighten collar until snug and the outer
end of the collar is flush with end of the barrel.
Reassembly
1.
2.
Make sure all parts are clean before reassembly.
Coat  new O--rings,  Uni--rings,  rod seal,  back--up
ring, and dust seal with with clean hydraulic oil.
A.  Install Uni--ring and O--ring to the piston.
B.  Install dust seal, O--ring, back--up ring, and dust
seal to the head.
Greensmaster 3250--D
Page 4 -- 87
Hydraulic System (Rev. I)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website