Toro 00062SL Rev I Greensmaster 3250 D Service Manual

6.
24)
Remove lock nut (item 25) and spring washer (item
that secure drive side groomer arm lift rod  to drive
side plate (Fig. 7).
3
7.
Remove lock nut (item 35), tab washer (item 34) and
4
plow bolt (item 27) that secure drive side groomer arm
assembly to drive side plate. Do not change height−of−
cut screw adjustment. Remove drive side groomer arm
assembly from cutting unit.
8.
Remove front roller assembly from cutting unit.
To prevent groomer shaft from turning when re-
Note:
1
moving driven pulley, use wrench on shaft flats to hold
shaft.
2
9.
Remove the flange nut (item 17) that secures driven
Figure 7
pulley (item 32) to groomer shaft. Remove driven pulley
from shaft. Locate and retrieve square key (item 31) that
locates pulley on shaft.
1.
2.
Cap screw
Front roller shaft
3.
4.
Groomer shaft assembly
Locknut/spring washer
Note:
To prevent  cutting reel  from turning when  re-
moving drive pulley, block reel with piece of wood.
10.Remove
(item 5) that secure drive  pulley (item 7) to the cutting
reel shaft. Slide drive pulley from cutting reel.
flange  head screw  (item  4) and  washer
2
11.
groomer drive  side plate  (item 10)  to the  cutting unit
frame. Remove the groomer drive side plate assembly.
Remove two shoulder nuts (item 8) that secure  the
1
12.Remove
plate (Fig. 8).
the cap plug (item 21) from non−drive side
Figure 8
Roller retaining cap screw
1.
2.
Cap plug
13.Remove
the flange  nut  that secures  the groomer
shaft to the non−drive side plate.
the groomer reel from the non−drive side plate.
seals, bushings and bearings in side plates
14.Pull
1
2
15.Inspect
for wear or damage. Replace components as needed.
Installation
3
1.
Park machine  on a clean  and level surface,  lower
cutting units completely to the ground, stop engine, en-
gage parking  brake and remove key  from the ignition
switch.
2.
LH  side plates.  Make sure  that  seals, bushings  and
bearings are properly positioned in side plates.
Apply a light coating of grease to seal lips in RH and
Figure 9
1.
2.
Drive side plate
Drive pulley
3.   Driven pulley
3.
Carefully place groomer reel assembly into the non−
drive side plate bearings taking care not to damage seal
in side plate. Thread flange nut (item 17) onto the shaft
threads but do not tighten.
4.
Make sure that groomer shim (item 11) is installed on
groomer drive side of cutting unit.
Greensmaster 3250−D
Page 7.2 − 9
Groomer (DPA Cutting Unit) (Rev. D)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website