Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Procedure for  Traction Drive  Hydrostat (P3) Flow
Test
CAUTION
This test measures hydrostat pump output (flow). Dur-
ing this test, pump load is created atthe flowmeter using
the adjustable load valve on the tester.
Use extreme  caution when  taking gauge read-
ings. The front tire on the ground will be trying to
move the machine forward.
1.
Make sure hydraulic oil is at normal operating tem-
peraturebyoperatingthemachineforapproximatelyten
9.
tion.
Slowly push traction  pedal into fully forward posi-
(10)
2.
minutes.
Park machine  on a level  surface with  the cutting
10.
Slowly close flow control valve until pressure gauge
units lowered  and off. Make sure  engine is off.  Make
sure the hydraulic tank is full.
reads 1000 PSI (69 bar).
Observeflowgauge.TESTERREADINGshouldbe
11.
a minimum flow of 13.3 GPM. Record test results.
CAUTION
12.
Releasetractionpedal,opencontrolvalveontester,
and turn off machine.
Before continuing further, read and  become fa-
miliar with Precautions for Hydraulic Testing.
13.
If specifications are not met consider the following:
3.
Make sure that traction pedal is adjusted to the neu-
A.  The traction  pedal and/or traction  speed may
need adjustment (see Traction Pedal in the Adjust-
ments Section).
tralposition(seeTractionPedalintheAdjustments    Sec-
tion).  Also, ensure  that  pump is  at full  stroke  when
traction pedal is pushed into fully forward position.
B.  The hydrostat needs to be repaired or replaced
as necessary.
4.
wheel if machine is equipped  with 3WD) to allow flow
through the traction circuit.
Block  up front  wheels  off the  ground  (also rear
C. Makenecessary  repairsbeforeperformingaddi-
tional tests.
5.
Disconnect hose from the upper hydraulic fitting on
the side of the hydrostat.
14. If  specifications are met,  check wheel  motor effi-
ciency (see Wheel Motor Efficiency Test in this section).
6.
Install tester with pressure gauge and flow meter in
series with the pump and the disconnected hose. Make
sure flow control valve on the tester is fully open.
15. If testing is complete, disconnect tester from pump
fitting and hose. Reconnect hose to pump fitting.
7.
Make sure functional lever is in the transport posi-
tion.
8.
50
Start engine and move throttle to full speed (2750 +
RPM) position.
Greensmaster 3250--D
Page 4 -- 35
Hydraulic System (Rev. I)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website