Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Procedure for Lower Cutting Units Relief Valve (R2)
Pressure Test
B.  For
machines
with
serial
number
over
230000000, reliefpressure should be 400 PSI(27.6
bar) higher than charge relief (R4) pressure (e.g.
if charge relief valve pressure is 100 PSI (6.9 bar),
the  lower  relief  valve  (R2)  pressure  should  be
approximately 500 PSI (34.5 bar)).
1.
peraturebyoperatingthemachineforapproximatelyten
Make sure hydraulic oil is at normal operating tem-
(10)
2.
minutes.
Park machine  on a level  surface with  the cutting
8.
If relief valve (R2) pressure is incorrect, adjust relief
units lowered. Make sure engine is off and the parking
brake is engaged. Make sure the hydraulic tank is full.
valve (R2) (see Adjust Manifold Relief Valves in the Ad-
justments section  of this Chapter). Retest  relief valve
pressure if adjustment is performed.
CAUTION
9.
gear pump and hose. Reconnect hose to hydraulic fit-
ting on pump.
After  testing is  complete, disconnect  tester from
Before continuing further, read and  become fa-
miliar with Precautions for Hydraulic Testing.
MANIFOLD FROM MACHINE
WITH SERIAL NUMBER
UNDER 270000000 SHOWN
S1
FRONT
3.
sure (see Charge Relief Valve (R4) Pressure Test in this
section).
Measure and record charge relief valve (R4) pres-
S3
4.
Use  same  tester   connections  as  described  in
Charge Relief  Valve (R4)  Pressure Test.  Fully open
control valve on the tester.
5.
50
Start engine and move throttle to full speed (2750 +
RPM). Make sure that cutting units are fully lowered
S4
and engage the cutting units.
S2
Note:
automatically turns off after approximately six  (6) sec-
onds.
The LOWER function is electrically  timed and
RELIEF
VALVE (R2)
Figure 16
6.
Watch pressure gauge carefully  while moving the
Raise/Lower -- Mow Control lever to LOWER and note
pressure that relief valve opens. Shut off engine and re-
cord test results.
S2
S3
FRONT
Note:
While  performing this  hydraulic  test, if  relief
pressurecannotbedeterminedwithintheLOWERfunc-
tion six  (6) second timeframe,  repeat this test  proce-
dure.
S4
Note:
The lower cutting units relief valve (R2) is in se-
ries with charge relief valve (R4). (R4) pressure will af-
fect (R2) pressure.
S1R1
7.
The lower cutting units relief pressure (R4) should
be:
MANIFOLD FROM MACHINE
WITH SERIAL NUMBER
OVER 270000000 SHOWN
A.  For   machines   with    serial   number   under
RELIEF
VALVE (R2)
220999999,
reliefpressure should be 150 PSI(10.3
bar) higher than charge relief (R4) pressure (e.g.
if charge relief valve pressure is 100 PSI (6.9 bar),
the  lower  relief  valve  (R2)  pressure  should  be
approximately 250 PSI (17.2 bar)).
Figure 17
Greensmaster 3250--D
Page 4 -- 43
Hydraulic System (Rev. I)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website