Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Reel and Bearing Removal and Installation
Removal (Fig. 58)
3
1.
Remove reel motor from the cutting unit and the cut-
ting unit  from lift  arm (see Cutting  Unit Removal  and
Installation).
2.
Place cutting unit on a level working surface.
3.
Remove shield rod (2) from frame by removing both
cap screws (5) and flat washers (4).
2
1
4.
Roller Removal and Installation).
Remove front roller from the cutting unit (see Front
Figure 59
3.
1.
2.
Reel shaft
Drive adapter
Adapter spline
IMPORTANT: Place strips of wood below the reel to
prevent the  reel from  dropping out  of the  cutting
unit when the bearing housings are removed.
2.
Inspect reel (1) as follows:
A.  Check reel shaft  for bending and  distortion by
placing the shaft ends in V−blocks. Replace reel if
necessary.
5.
Remove both  bearing housings (10)  by removing
the tapered lock nuts (8) and tapered screws (14) secur-
ing the housings to the frame. Pull both housings away
from the frame and away from the reel ends.
B.  Check reel blades for bending or cracking. Re-
place reel if necessary.
6.
Remove reel (1) with the bearings (12) and grease
seals (13) from the cutting unit.
C. Check drive adapter inside of reel shaft. Adapter
should  be free  of  bending and  distortion. Check
splines for excessive cracks and distortion. Replace
reel if necessary (Fig. 59).
7.
(11)
Remove bearing  spacer (29)  and flat  wire spring
from their  bearing housings (10). Clean  inside of
each housing. Both housings should be free of dirt and
debris.
D. Check  service limit  of reel diameter  (see Reel
Grinding Specifications in Preparing Reel for Grind-
ing).
Note:
If bearings (12) are removed from the reel (1),
replace grease seals (13).
3.
lows (Fig. 58):
Inspect bearings (12) and grease seals (13) as fol-
8.
seals (13) from the reel (1) as follows (see Inspection be-
low):
If  necessary,  remove  bearings  (12)  and  grease
A.  Seals must be free of cracks and tears. Replace
seals as necessary.
A.  Prevent damage to bearings by pulling on the in-
ner bearing race.
B.  Bearing roller balls must be free of deformation
and scoring. Replace bearing if necessary.
B.  Use  bearing  puller  to  remove  bearings  and
seals.
C. Bearing must spin freely and have minimal axial
play. Replace bearing if necessary.
Inspection
4.
bearing housing of cutting unit with  No. 2 general pur-
pose grease.
Using a  hand pump  grease gun,  fill cavity  in the
1.
Inspect splined coupler (32) as follows (Fig. 58):
A.  Remove retaining  ring (31)  and  drive coupler
from the reel shaft (1).
B.  Clean drive coupler. Coupler  should be free of
dirt and debris.
C. Drive coupler should be free of bending and dis-
tortion. Check splines for excessive cracks and dis-
tortion. Replace coupler if necessary.
SPA and 4−Bolt Cutting Units (Rev. A)
Page 7 − 34
Greensmaster 3250−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website