Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Inspection (Fig. 46)
Remove all nicks and  burrs from all parts with  an
Note:
pocket opposite the external drain port.
Make sure idler gear  is installed into the gear
1.
emery cloth.
3.   Dip idler gear and drive shaft assemblies into clean
hydraulic oil. Install both assemblies into the cover as-
sembly gear pockets. Make sure that both gears mesh.
CAUTION
4.
Coatnewloadplateassemblylightlywithpetroleum
jelly.Installloadplateassemblyontoidlergearanddrive
shaft assemblies.  Make sure  seal of assembly  faces
away from the gear face.
Use eye protection such as goggles when using
compressed air.
5.
Slide body assembly over the idler gear and drive
2.
pressed air.
Clean all parts with solvent. Dry all parts with com-
shaft assemblies onto the cover assembly. Make sure
that none  of the  parts become displaced.  Install hex
socket head screws and washers. Hand tighten screws.
3.
Inspect drive shaft and idler gear assemblies.
6.
Rotate drive shaft to make sure gears mesh proper-
ly.Torquehexsocketheadscrewsfrom190to210in--lb
to 23.7 N--m).
A.  Bushing points and seal areas should be free of
excessive excessive wear and rough surfaces.
(21.5
B.  Gear faces should be free of excessive scoring
and wear.
7.
body assembly.
Install new spacer onto the drive shaft and into the
C. Gears should be free of excessive  wear, nicks,
and, missing or  broken teeth. Break sharp  edges
with emery cloth.
IMPORTANT: Use extreme care when installing the
shaft seal to prevent damage to the seal.
8.
Install new shaft seal as follows:
D. Replace if either shaft is visibly bent.
Inspect cover and body assemblies.
A.  Make sure that the bore of the body assembly is
clean and free of burrs and nicks which could dam-
age the seal.
4.
A.  Bearing needles  should  remain  in  cage and
movefreely.Ifneedlebearing(s)   needreplacement,
the entire assembly must be replaced.
B.  Lubricate lips of the seal generously with clean
No. 2 multipurpose lithium base grease. Apply Loc-
tite gasket eliminator 515 or equivalent to the outer
edge of the metal case of the seal.
B.  Sealingfacesandgearpocketsshouldbefreeof
excessive scoring.
Assembly (Fig. 46)
Coat new seal ring lightly withpetroleum jelly.Install
C. Make sure metal case of shaft seal faces away
from the motor. Use seal installer to press shaft seal
squarely into the bore.
1.
seal ring into matching groove on the body assembly.
9.
Install retaining ring into bore of the body assembly.
2.
pockets of the cover  assembly. Install dowel pins into
body assembly.
Apply a  thin coat  of petroleum  jelly to  both gear
10. Lubricate motor generously with clean hydraulic oil.
Greensmaster 3250--D
Page 4 -- 77
Hydraulic System (Rev. I)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website