Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Functional Control Lever Reed Switches and Actuator
Both reed switches are normally open. They close when
the  actuator comes  in  close proximity  to the  switch.
These switches are used to sense the Functional Con-
trol Lever in either the NEUTRAL or MOW position.
3
1.
Make sure the  engine is off. Disconnect  electrical
1
connectors to both  switches. Check continuity of  both
switches  by  connecting a  multimeter  (ohms  setting)
across the connector terminals.
2
2.
Place the Functional Control Lever in the NEUTRAL
position. The NEUTRAL reed switch should have conti-
nuity and the MOW switch should be open (Fig. 9).
3.
Place  the Functional  Control  Lever in  the  MOW
Figure 9
position. The  NEUTRAL reed  switch should  be open
and the MOW switch should have continuity (Fig. 9).
1.
2.
Mow reed switch
Neutral reed switch
3.
Actuator
4.
switch and the traction bracket should be 0.725 to 0.775
inch (18.4 to 19.7 mm) (Fig. 10).
The  distance between  the  sensing  end  of each
0.725
(18.4
to 0.775 inch
to 19.7 mm)
REED SWITCH
5.
To adjust or install actuator,  place lever in neutral,
position actuator in lever until the NEUTRAL switch just
closes,  and then  rotate  actuator two  complete  turns
closer to switch.
6.
nuts 30o past finger tight.
When adjusting  switches or  actuator, tighten  jam
CONNECTOR
TRACTION BRACKET
Figure 10
7.
After switch or actuator adjustment, check continu-
ity of both switches and interlock operation (See Verify
Interlock System Operation). Readjust switch or actua-
tor if necessary.
Backlap Switch (If Equipped)
The backlap switch is located on the hydraulic manifold
(when the Backlap Kit is installed). The switch is normal-
ly open and closes when the backlap knob is turned to
the backlap position.
2
3
1.
With the engine off, disconnect electrical connector.
1
2.
Check the continuity of the switch by connecting a
multimeter (ohms setting)  across the connector termi-
nals.
3.
Turn  the backlap  knob  clockwise to  the  backlap
position   while  watching   the  multimeter.   Continuity
should be made as the switch closes.
4.
Turn the backlap knob counterclockwise to the mow
position   while  watching   the  multimeter.   Continuity
should be broken as the switch opens.
Figure 11
1.
2.
Connector
Backlap switch
3.
Backlap knob
5.
Reconnect the electrical connector.
Electrical System (Rev. C)
Page 5 − 12     Rev. H
Greensmaster 3250−D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website