Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Fuel Tank Removal (Fig. 18)
Park machine on a level surface, lower cutting units,
stop the engine, engage parking brake, and remove the
key from the ignition switch.
Fuel Tank installation (Fig. 18)
1.
1.   Position fuel tank (2) to the mounting plate (13). Be
careful not to damage any fuel hoses.
A.  Apply antiseize  lubricant to the  threads of  the
three cap screws (16).
DANGER
B.  Secure fuel tank to the plate with three flat wash-
ers (4) and cap screws.
Diesel fuel is flammable. Use caution when stor-
ing or handling it. Do not smoke while filling the
fuel tank. Do not fill fuel tank while engine is run-
ning or in an enclosed area. Always fill fuel tank
outside and wipe up any spilled diesel fuel before
starting the engine. Store fuel in a clean, safety−
approved container, and  keep the cap in  place.
Use diesel fuel  for the engine only;  not for any
other purpose.
C. Torque cap screws from 30 to 60 in−lb (3.4 to 7.8
N−cm).
2.
Connect fuel  hose (18) to the  fuel tank with  hose
clamp (10).
3.
Connect fuel hose (23) to fuel fitting (11) with hose
clamp (26).
4.
Install mounting plate (13) to the frame as follows:
2.
Drain fuel tank (2) as follows:
A.  Position mounting plate to the frame. Make sure
to align  plate holes with  frame holes and  support
bracket (28).
A.  Close fuel shut−off valve (9) below the fuel tank.
B.  Disconnect fuel hose (21) from the fuel shut−off
valve (9). Place  hose into a  suitable container for
draining the tank
B.  Secure mounting plate to the frame and support
bracket with  two flat  washers (14)  and three cap
screws (6).
C. Drain  fuel tank completely  by opening the fuel
shut off valve.
5.
6.
7.
Connect fuel hose (21) to the fuel shut−off valve (9).
Open fuel shut−off valve (9) below the fuel tank.
Fill fuel tank with fuel (see Fill Fuel Tank). Check fuel
3.
(2)
Gain access to the fasteners securing the fuel tank
to the mounting plate (13) as follows:
A.  Remove three cap screws (6) and two flat wash-
ers (14) securing mounting plate  to the frame and
support bracket (17).
lines and tank for leaks.
B.  Lift and support the mounting plate up from the
rear of the machine.
4.
Loosen hose clamp (26) and disconnect fuel hose
(23)
from fuel fitting (11).
5.
(18)
Loosen hose clamp (10) and disconnect fuel hose
from fuel tank (2).
6.
Remove three cap screws (16) and flat washers (4)
securing the fuel tank (2) to the mounting plate (13). Re-
move the tank from the mounting plate being careful not
to damage any fuel hoses.
Greensmaster 3250−D
Page 3 − 15
Engine
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website