Toro 00062SL Rev I Greensmaster 3250 D Service Manual

Specifications
4−BOLT
ADJUST UNIT
SINGLE POINT
ADJUST UNIT
Figure 14
Height−of−Cut (HOC):  Cutting height  is adjusted  on
the rear roller  by two vertical  screws and held by  two
locking  capscrews.  Bench  HOC  range  is  3/32  inch
placeable roller that may be moved to change transport
height.
Bedknife: Replaceable, 13−screw, single edged, high
carbon steel bedknife austempered to  RC 48−55, fas-
tened to a machined cast iron bedbar. Tournament bed-
knife is standard.
(2.4mm)
to 1−1/32 inches (26mm). Cutting units will de-
liver  differing  effective  height−of−cuts depending  on
their configuration. In fact, effective cutting height may
be influenced by  the following factors;  turf conditions,
roller profiles, cutting unit attitude, cutting unit accesso-
ries, weight of cutting units and bedknife profile. There-
fore  bench setting  a cutting  unit  does not  equal  the
effective (actual) height of cut you achieve. You need to
determine how  to adjust  your cutter  on the  bench to
achieve a comparable height of cut to a cutting unit of a
different configuration, model or brand.
Bedknife Adjustment (Single Point Adjust): A single
control screw has detents corresponding to 0.0007 inch
(0.018
mm) bedknife movement for each indexed posi-
tion. A linear adjustment on the bedbar  left end allows
leveling of bedknife to reel blades. A centered lever arm
regulates knife to reel contact with two rubber bushings
acting as pivots.
Reel Construction: Reels are 5 inches (13cm) in diam-
eter, 21 inches  (53.3 cm) in length.  High carbon steel
blades are welded to 5 stamped steel spiders and heat
treated to RC 48−54 hardness. The reel is ground for di-
ameter, concentricity, and back grind.
Bedknife Adjustment (4−Bolt Adjust): Two opposing
screws on each end of the bed bar are used to level and
regulate bedknife to reel contact.
Front Roller: Standard front roller is a 2.5 inch (6.4 cm)
diameter full radius Wiehle. The right bracket has an ec-
centric shoulder bolt to  provide leveling. A second ec-
centric may be added  to the left bracket for  increased
leveling range. Roller has a through shaft with grease-
able ball bearings.
Reel   Bearings:   Two   double   row   ball    bearings,
(30
mm I.D.) are press fitted onto the reel shaft. An in-
verted seal pressed onto  reel shaft. Bearing side load
maintained by a wave washer, no adjusting nut.
Reel Drive: The reel weldment shaft is a 1.375−inch di-
ameter tube with drive inserts  permanently pressed in
both ends. A replaceable floating coupler with an inter-
nal eight tooth spline is factory installed on the right end,
and held in  place by a snap ring.  The floating coupler
may be moved to the other end when the cutting unit is
used on the tractor front right position.
Rear Roller: Standard rear roller is a 2 inch (5.2 cm) di-
ameter smooth steel  roller. Roller has a  through shaft
with greaseable ball bearings.
Counterbalance Weight: The end of cutting unit oppo-
site the reel motor has a weight with a spin flange like the
reel motors for  easy installation. The weight seals  the
bearing area and balances the reel motor’s weight dur-
ing cutting.
Frame Construction: Single top tube is welded to two
sideplates. A bolt−in cross rod acts to set the front frame
width and stiffen the assembly. The lift straps have a re-
Greensmaster 3250−D
Page 7 − 3
SPA and 4−Bolt Cutting Units (Rev. A)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 308 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website